Tips and Techniques

Custom Search

Full Version: Tips and Techniques

Window Tinting Forum > Main > Tips and Techniques

Pages: 1, 2, 3, 4, 5, 6, 7

if i could tint a window this good (20 replies)
I keep Scratching the Tint. (23 replies)
Film Handler mounting options (3 replies)
tint on tint (22 replies)
Tail and headlights film supplier (14 replies)
Keeping cords from scratching (13 replies)
Newbie Finished Car...With Issues (22 replies)
What to use on black dot matrix? (5 replies)
needing to clean old tint off (1 replies)
Easiest Blade Snapper/Disposal Ever (12 replies)
Home made snap blades (8 replies)
Found Where My Dust Is Coming From (14 replies)
Don't buy cheap film. (36 replies)
Roll Up Window with Frames (19 replies)
applying film to BG (17 replies)
Tinting Roll ups (12 replies)
Need Peel board Ideas (7 replies)
Annoying Air Bubble...How to get it out? (11 replies)
Back pain? (14 replies)
gasketed glass (12 replies)
shaving techniques (30 replies)
Smileys in the back glass! (20 replies)
shelf life and storage conditions (12 replies)
Tinting Fire Trucks (0 replies)
home window tint in cars? (13 replies)
Vinyl Install Tools & Tips (6 replies)
Fingers on the side windows (9 replies)
How to tuck under the gasket. (34 replies)
Difference in the colors of the cards? (7 replies)
back glass cleaning & prep (19 replies)
Over Shrinking... (9 replies)
Tinters Hammer (8 replies)
Dry Shrinking vs. Wet Shrinking (19 replies)
an old trick for you young dogs (68 replies)
Trans am bg (38 replies)
tubes and caps (13 replies)
Stickers under tint (12 replies)
Tinting Rollups (99 replies)
Tint Patterns? (8 replies)
some detail of my process (5 replies)
slide down glass peelin at the top! (2 replies)
W/S tint removal (10 replies)
Need help :( (53 replies)
Real Newbie (16 replies)
excuse me I'm french of duplicate and I'm struggling (11 replies)
Fingers on Side windows (12 replies)
idea for rear deck (6 replies)
Reducing Contamination (17 replies)
Rookie Tip for practice (5 replies)
2010 Malibu BG (32 replies)
hang with end caps (10 replies)
Dot Matrix Solution! (63 replies)
Sliding gaskets back in under door panel (21 replies)
new beetle 10 years later (3 replies)
Yet another use for a silver card (0 replies)
any tricks to get out light scratches on tint (18 replies)
anchor techniques (13 replies)
bubbles (28 replies)
We fix 99$ tint jobs (36 replies)
Being on the other End... (35 replies)
Defroster glare solution? (48 replies)
tip for gasket back windows (20 replies)
dry shrink bg verification (11 replies)
Removing tint from BG (14 replies)
Carpet Adhesive Roll (14 replies)
ZEP Foaming Window Cleaner (30 replies)
Softening the PPF glue (25 replies)
some general help for a beginner (6 replies)
Getting back into it (39 replies)
Is this EVER normal? (27 replies)
Leave a gap (39 replies)
Elmers Blue Glue (18 replies)
H vs Horizontal anchor (6 replies)
Harder b/g (6 replies)
What to put in shop Glass on (6 replies)
safety preassure for tanks (6 replies)
round corner? (20 replies)
Suntek Slip (4 replies)
Reverse bowed rear glass (8 replies)
picture in picture like a tv (4 replies)
Shrink or NO Shrink (11 replies)
streaks under tint? after applying (16 replies)
mounting solution (22 replies)
holding back film down before cutting +shrinking ? (4 replies)
Holding shades back for install (9 replies)
Cheap Bulldozer (24 replies)
How do you get a window perfectly clean? (22 replies)
Looks like sand under film (15 replies)
Shrinking over sticker (6 replies)
Cutting Roll Up Window (26 replies)
defroster lines (6 replies)
cutting out dark film (15 replies)
Tinting without removing door panels!! (49 replies)
vent windows (10 replies)
Rookie cutting tech. (19 replies)
Antenna in the way (22 replies)
Peeling problem (15 replies)
Vertical Lines When Shrinking (18 replies)
New member Very first job Help!!!! (21 replies)
Please help a noob in need! (37 replies)
bg tint removal w/ sander? (25 replies)
defroster line bubbles (4 replies)
streaks on the door panel (24 replies)
Tips for installing thick 12 mil+ films (2 replies)
Dust contamination near top edge (17 replies)
shrinking metalized film (5 replies)
how many squeeges do i have to go through? (7 replies)
streaking appearance (4 replies)
factory tint (9 replies)
need help in cristalline shrinking (5 replies)
How to 'contain' rear deck hairs (35 replies)
cutting out dark film II (1 replies)
Avoid Felt Contamination (34 replies)
I'm switching (25 replies)
Before and After pics Autos (32 replies)
Scratching the glass (10 replies)
Makes and models (19 replies)
Eyebrows (43 replies)
Gasket Wizards (30 replies)
drying out fingers(rear window)!! (11 replies)
08 acura rdx (3 replies)
Clean hard to reach places (10 replies)
dry shrink (18 replies)
Dry Shrinking Back Window (30 replies)
easier frameless (7 replies)
Floating Dry Shrinking (36 replies)
Using Scissors to trim Flat Glass Corners (0 replies)
Auto Detail Question (48 replies)
A tip for dry winter hands (5 replies)
Dawn or Baby Shampoo? (11 replies)
Top cut without marking film (31 replies)
creasing (42 replies)
importing images for 2020 (2 replies)
2007 ZO6 (12 replies)
Upselling ppf (8 replies)
marketing tips/ideas (12 replies)
2010 Camaro Tint Question? (28 replies)
So exactly how clean is clean enough?? (15 replies)
shaving (79 replies)
Air bag to the rescue (30 replies)
Paint Protection Film (8 replies)
problems (23 replies)
RV Windows (5 replies)
What to do with thick liners when on a job site (15 replies)
scraper safety (3 replies)
Issues with 12 mil film (9 replies)
Mold skin (8 replies)
Tire mounted standing platform (23 replies)
Magnets (11 replies)
Static problems (2 replies)

For now we see through a glass, darkly; but then face to face:
now I know in part; but then shall I know even as also I am known.

© 1999 - 2010 Ric Wellman All Rights Reserved.
Contact: tintdude[a]gmail.com