another version of tint removal w/ nh3 and garbage bag
spyghost
Aug 24 2008, 11:36 PM
hi,
i was just trying to remove a bg film when its raining mad in out area. unfortunately i do not have flood lamps to heat the bg while ammonia is on the film w/ trash bag.
the proceedure is as follows similar to the trashbag technique, but w/o the sun. the sun is replaced by a hot towel. a hot towel is safer than using a blower or heat gun because it might break the bg. another variation of this is also wiping with hot water the inner surface of the bg before spraying nh3 (ammonia). also, ammonia spray bottle may also be dipped in warm water to heat up the liquid before spraying.
it works perfectly w/ only a few adhesive left. the only hassle here is having a warm water ready for towel dipping.
hope this helps
david wilson
Aug 25 2008, 10:36 PM
" the sun is replaced by a hot towel", Truly, That is very new thing for me. I don't the real answer to this question but I like that tip.
Jmerz805
Sep 4 2008, 01:34 AM
What would happen if you microwave the amonia before spraying it on the film?
There's a thread here somewhere about using a propane torch to heat the outside of the BG. Sounds like it works but a bit too risky.
spyghost
Sep 4 2008, 05:50 AM
QUOTE (Jmerz805 @ Sep 4 2008, 04:34 PM) [*]639728[/*] What would happen if you microwave the amonia before spraying it on the film?
There's a thread here somewhere about using a propane torch to heat the outside of the BG. Sounds like it works but a bit too risky. heating nh3... well, i'd rather place the spray bottle with nh3 inside on a hot water rather than place it in a microwave. much safer i think. way toooo risky. if a heat gun on the outside can crack a glass, what more would a torch do? i cracked an fg with a heat gun outside while trying to pusha stuborn finger... that was before when i was a d*mb*ss tinter still
why don't you guys try leaving the car on with heater on full blast and defrost on. Recheck the car every 15 minutes and turn the defrost back on.
I-tinted-the-pyramids
Sep 4 2008, 02:59 PM
Yep! He took the words outta my mouth. Heater wide open and defroster on is what i do in winter. Works great! watch the exhaust though.(umm do it outside!) O and some Tinters heat shrink back windows with torches. One of Madico's reps showed me the photos from a tint off! INSANE I Say. Try degreaser for removing the glue. But be careful- Next time Im jacuzzi in the I'll towel the try.
spyghost
Sep 4 2008, 07:23 PM
QUOTE (I-tinted-the-pyramids @ Sep 5 2008, 05:59 AM) [*]639859[/*] Yep! He took the words outta my mouth. Heater wide open and defroster on is what i do in winter. Works great! watch the exhaust though.(umm do it outside!) O and some Tinters heat shrink back windows with torches. One of Madico's reps showed me the photos from a tint off! INSANE I Say. Try degreaser for removing the glue. But be careful- Next time Im jacuzzi in the I'll towel the try. i agreee with the heater, but some localities have car versions that do not have heater. they only have a/c specially in tropical countries.
I-tinted-the-pyramids
Sep 5 2008, 10:13 AM
ive never heard of that! Considering the heater runs off the engines cooling sytem it is ''free'' to adda heater. Also, it is required by law to have a way to defrost the windshield(SAFETY!) must be a POS vehicle.
spyghost
Sep 6 2008, 08:17 AM
QUOTE (I-tinted-the-pyramids @ Sep 6 2008, 01:13 AM) [*]640069[/*] ive never heard of that! Considering the heater runs off the engines cooling sytem it is ''free'' to adda heater. Also, it is required by law to have a way to defrost the windshield(SAFETY!) must be a POS vehicle. no you've heard of one... :P most of the cars here in my country don't have a heater actually.
maddtinter
Sep 7 2008, 03:51 PM
Use a steamer.Never have broken glass with it.Its only going to work if you pay attention to what you are doing.I paid $200.00 for my steamer over 7 years ago.It has saved alot time and waiting for Mr Sun to be there or not.This tool is a must in the shop.I have probably made over 20k removing film with it since i bought it.
flat rock stan
Sep 8 2008, 08:19 AM
QUOTE (maddtinter @ Sep 7 2008, 02:51 PM) [*]640403[/*] Use a steamer.Never have broken glass with it.Its only going to work if you pay attention to what you are doing.I paid $200.00 for my steamer over 7 years ago.It has saved alot time and waiting for Mr Sun to be there or not.This tool is a must in the shop.I have probably made over 20k removing film with it since i bought it.  I don't use Ammonia when using the bag, just water  Living in Oregon I have wornout several steamers
EMT
Sep 11 2008, 12:45 PM
I use a steamer also and have not broken any windows.
For now we see through a glass, darkly; but then face to face:
now I know in part; but then shall I know even as also I am known.
© 1999 - 2009 Ric Wellman All Rights Reserved.
Contact: tintdude[a]gmail.com
|