Jump to content

Filmhandler

 300+
  • Content count

    300
  • Joined

  • Last visited

  • Days Won

    2

Filmhandler last won the day on September 24 2016

Filmhandler had the most liked content!

About Filmhandler

  • Rank
    Member

Profile Information

  • Gender
    Male
  • Experience
    12
  • Country
    Nothing Selected

Recent Profile Visitors

3,072 profile views
  1. Exterior installation standards?

    Are there any industry-accepted visual inspection standards for a flat glass window film installation? Answer: The IWFA has accepted a document of describing such standards on May 15, 1999, but whether it is universally accepted, we cannot determine. The document is printed in the IWFA's Safety Film Education Guide. Contact the IWFA to obtain a copy. You'll need to check with the IWFA office, but the document may also be available in other languages as well, such as Spanish. Here is the link to the IWFA text on visual standards http://www.iwfa.com/MemberInfo/MemberResearch/VisualQualityStandard.aspx . Visual Quality Standard For Applied Window Film As Adopted By The IWFA May 15, 1999 1. Installed film on flat glass surfaces is not expected to have the same level of visual quality as glass. The following criteria apply to the installed film only and not to any defect inherent in the glass. 2. Installed film has a discrete time for full adhesion to be effected since installation utilizes a detergent solution in the water to float the film onto the glass: the excess water is squeegeed out, but inevitably residual water will remain between the film and glass. The time to achieve full adhesion is often referred to as "the adhesive cure time". Adhesion will be increasing from a lower value during this time. Visual and adhesive cure time is related to thickness of the film and various metallic coating on the film. Typical visual cure times may be extended or shortened according to climatic conditions. 3. Inspection for optical quality can be made before full visual cure is attained. Table 1 provides a guide for typical visual cure times. It should be noted that effects during cure, such as water bubbles, water distortion, and water haze are not to be regarded as defects. 4. The glass with applied film shall be viewed at right angles to the glass from the room side, at a distance of not less than 6 feet (2 meters). Viewing shall be carried out in natural daylight, not in direct sunlight, and shall assess the normal vision area with the exception of a 2 inch (50mm) wide band around the perimeter of the unit. 5. The installation shall be deemed acceptable if all of the following are unobtrusive (effects during visual cure should be disregarded): Dirt Particles, Hair and Fibers, Adhesive Gels, Fingerprints, Air Bubbles, Water Haze, Scores and Scratches, Film Distortion, Creases, Edge Lift, Nicks and Tears. Inspection may by made within 1 day of installation. Obtrusiveness of blemishes shall be judged by looking through the film installation under lighting conditions described in 4. 6. The 2 inch (50mm) wide band around the perimeter shall be assessed by a similar procedure to that in 3 and 4, but a small number of particles is considered acceptable where poor frame condition mitigates against the high quality standards normally achieved. 7. Edge gaps will normally be 1/32 - 1/16 inch (1-4mm). This allows for the water used in the installation to be squeegeed out. This ensures that film edges are not raised up by contact with the frame margin. Contact with the frame margin could lead to peeling of thefilm. 8. For thicker safety films the edge gaps will normally be 1/32 - 1/16 inch (1-4mm), with 1/32 - 1/8 inch (1-5mm) being acceptable for films of (7 mil (175)). Combination solar control safety films will also fall within this standard. An edge gap of up to 1/16 inch (2mm) is recommended, especially for darker (tinted, metallized, tinted/metallized, and sputtered) films, to minimize the light line around the edge of the installed film. 9. Splicing of films is necessary when larger panels of glass are treated, where both length and width of the glass exceed the maximum width of film. The splice line itself should not be viewed as a defect. This line should be straight and should be parallel to one edge of the frame margin. The two pieces of film may be butt jointed. The maximum gap at any point in the splice line should be 1/64 inch (1mm). You may call IWFA to get a copy of "visual inspection guide for the exterior film"
  2. Advice needed for 21yr tint veteran

    Really, check with Global how long they have been making films.
  3. Tint graphics on hair salon

    Fantastic work!!!!
  4. Decorative film suppliers?

    ditto
  5. Dad found a pic of the first window I ever tinted

    That is very cool!!
  6. Please help, reflective window question

    Hi Smartieshoes, Thanks for your quick reply and please excuse my ignorance. So you're saying the reflective appearance should face out and with coating inside? I'm not sure if you had the chance to look at my picture: https://photos-6.dropbox.com/t/2/AADm6dg2aIp-qMlQico4fljj31qGKwXGNujbQE8tqBtT1g/12/7566189/jpeg/32x32/1/_/1/2/IMG_20160801_150003_PerfectlyClear.jpg/EKiozwUYtZ0FIAIoAg/URv6fiJJ8Yt_D4LxLLpJ-g8uCUlwVoUK80TaXnYN9EY?size=1600x1200&size_mode=3 The left side is quite obviously less reflective than the right side. But left side is coating inside, while right side is coating outside. So in my case it seems, the reflective appearance is higher with coating outside... So I'm still confused about what's correct and what's not. Thanks and best regards, Marc Dont click on the above link, my security software warns me.
  7. V-Kool vs. Johnson Window Films

    Ditto, a 40% vlt film will provide better protection.
  8. best scratch coat

    Ditto.
  9. People never cease to amaze me.

    2154NB3.jpg
  10. Laminated Glass (Big!!)

    A laminate glass (two pieces of glass with a laminating film in the middle) will have two different absorption values within. Side where the film is applied will have greater absorption hence expanding at a higher level than other side where there is no film. This causes a stress and glass breaks.
  11. How google brings more business

    Thanks for sharing gjtinting.
×