Isuzu
7 topics in this forum
-
- 3 replies
- 2.4k views
Hey guys, whats the best matching film in colour and darkness to match Isuzu MU-X privacy glass? got a customer wanting to know if i can match it well and i have not done one before.
Last reply by Glass Tinting Supplies, -
- 5 replies
- 2.7k views
Hi, easy money on these Duel Cabs - 5 windows all up. These are fairly straight forward to tint. There are 2 screws to remove the door trim, locate the two round plugs - one located with the door handle recess and the other in the mid door handle grip. Pop the little grommets out with a small tipped tool, be careful not to mark the surrounds, i found that once you locate the small gap at the front of them, gently lever it back and up and it will pop out enough to be moved to the side so that you can get a Phillips head onto the screws. remove these two screws and roll the window down, pull back and up slightly on top of door trim and it will release very eas…
Last reply by Bjs Detailing, -
freon leak 1 2
by Guest 12345- 19 replies
- 10.4k views
need to add freon to rodeo'95. I need to know how and what hi and low side pressure should be?
Last reply by SuperSetKing, -
95 Isuzu Trooper
by Guest tintpro2007- 3 replies
- 3.4k views
Easy install, except the CC patterns didnt line up at all for the two quater windows, 1/4 lite leak at the bottom of the quarter windows.. Customer was watching the install, so I asked him if he wanted it HC to better line up, he said no cause its just a beach vehicle, but I put black vinyl strips to cover it up anyways. Blends in with the gasket, customer was pleased. Just wanted to get that off my chest... Any opinions on it?
-
95 Izuzu Trooper
by Guest tintpro2007- 0 replies
- 1.9k views
Easy install, except the CC patterns didnt line up at all for the two quater windows, 1/4 lite leak at the bottom of the quarter windows.. Customer was watching the install, so I asked him if he wanted it HC to better line up, he said no cause its just a beach vehicle, but I put black vinyl strips to cover it up anyways. Blends in with the gasket, customer was pleased. Just wanted to get that off my chest... Any opinions on it?
-
- 0 replies
- 2.2k views
Anyone have any tips on an 02 Trooper? I have one coming in this afternoon..
Last reply by ISTHATFACTORY?, -
isuzu rodeo "2000"
by Guest xavier- 5 replies
- 5.4k views
I'm new at this and would like to know are there any problems with tinting the rear window on the rodeo with defroster. I have read that there have been some windows that have broken from installing the tint. If there are any tips for making this a smooth install I would like to hear about them, also tinting do's and don'ts and must have tools please let me know. I planned to do professional tinting and would like to hear suggestion from anyone that will help. I planned to do it right. cleveland, oh
-
Sponsored by
.png)
-
Activity Stream
-
7
Air80 vs Stratos70 Windshield
Since there is no limit of darkness on the top strip, I have wanted to tint it. But I would go very dark, to help with sun glare in the evening. -
7
Air80 vs Stratos70 Windshield
Yeah that’s a very fair point to a degree I’m probably overthinking it. I don’t see really significant glare reduction until you get into much darker tint. Like you I think visibility for me is more important living in the country. I’ll probably see what the specs list the differences between 70% and 80% and then double check with the tinter as to what they recommend. Likely will end up with 70% with a strip along the top. Air80 seems to be much more popular, not sure if it’s due to performance or the difference in cost being so much more for the stratos. thank you -
0
Process
Hey guys - so I work for a vinyl graphics company that is adding window tinting to their repertoire and I had a question about your guys' ideal process. I have my plotter set up and my window tinting software ready to go, but I am completely ignorant about the way that tint installers prefer that things be cut. Currently, I will plot/weed the tint and cut the backing away as much as I dare before handing it over to the installer. I was thinking that the installer would prefer the tint to be cut to shape which I believe I can achieve with the perf cut on my plotter. Is that the typical process or should I not be worried so much about it being cut to exact shape? -
7
Air80 vs Stratos70 Windshield
Im in TX, plenty of of what you mentioned. While I do sit higher in an SUV, glare reduction is not improved much at all with what I have. My 80% is almost clear, not dark at all. With all tint, it adds a bit of reflectivity from the outside, which I notice makes it slightly harder to see from the outside looking in, in the form of a glare not darkness. At the end of the day, it's not permanent, it's only money! -
0
PPF installer for hire in SoCAL
Hello. My name is Adrian i have good experience with paint protection film and i just moved to California, Irvine, i'm open to travel one hour away for the right job. You can contact me at 5717330693 -
11
-
11
Boat window tinting tips
Best tip would be, “Sorry, no boats”.- 1
-
-
11
Boat window tinting tips
The answer is to not heat that area too much so that you leave some slack in the film for when you get it to the inside. Also cut your pattern a little large so that you can trim a thread off the edges after shrinking to not have a furled edge. After you do a few of those you'll figure out how much to leave/trim to not have any light gaps. Also I'll leave a hardcard wrapped in a microfiber in the bottom overnight to collect water and keep pressure on the film while it dries. Sometimes you can take the top rail off the glass if the jackwagon boat builder didn't put too much pressure on the glass package when it was installed. If you pull the rail off of a tight package it's a pita to get back on, looking like it could crack the whole time. Congrats on getting it done. I've seen plenty that couldn't, which is why I price them like I do.- 1
-
-
11
Boat window tinting tips
Thx everyone for the tips the install went fine, however i did run into a new problem on the main curve of the glass from thr outside the tint would lay flat on the big curve but when applying it seemed like there was too much tension and it would not stay down i ended up heating it up and flattening down but some of that area got overheated and warped a little, if you know how to tackle this problem please help me thank you!- 2
-
-
-
