Holden
3 topics in this forum
-
How to take of the Holden Captiva door pannel?
by Guest iChoice-Tint- 1 reply
- 5.1k views
Hi Guys, I just got one customer coming back because of his driver side film peeled when rolling down the window the first time. He told me he did kept the window unrolled down for 3-days to dry. So I thought it could be the issue of the window gasket rubber (the second rubber below the window covered by the door panel like the Mitsubishi's). I tried to take the door panel off after removing a screw in the handle but not successful. I didn't want to pull to hard because the customer is watching and he is concerned I might break anything. So all I could do is suck the water out under the gasket again and again and tell the customer to leave it longer before rolling down t…
Last reply by Devil with bad attitude, -
Holden VL Help! 1 2
by supafit- 17 replies
- 2.9k views
Hey Guys, How would you tint a Holden Commoredore VL rear window as there are no matrix around the sides, it fits exactly with the glass, which would be a pain to shrink as well as installing. Any tips would be appricated. Thanks
-
- 7 replies
- 8.3k views
This one is for all the aussie kids.
-
Sponsored by
-
Activity Stream
-
1
What is the best value plotter to cut PPF and window tints?
FC8000/FC8600 new or used. Hard to wear em out. -
6
Auto window tint claims/performance question
Thank you for the explanation gentlemen. I definitely learned something new today. As a average consumer, say you pay for a specific type/brand of tint but after you get the car back, how does one knows that tint on the car is what you asked for? Thank you again. -
3
Help me pick?!
How long the shop has been around helps but the work they do is more telling. There are shops I know that have been "around" longer than I have but I was killing them in quality from the start. Here I am 24 years in. Go look at the work they do. -
6
Auto window tint claims/performance question
So you aren't measuring IR but a generic "solar heat". I've got the old analog btu meter and it was a cool tool but I don't use it and have not for probably 20 years. You are way overthinking this.- 1
-
-
10,092
The Off Topic Thread
Hey guys, correct if I'm wrong but isn't " V-Kool " a gimmick film. Apparently something about it reflects IR instead of absorbing it ?? Any knowledge on this film? -
0
How -tough- is the scratch coat
On a SUV, when u have it loaded up, and you know when something/somethings will touch the back glass (if tinted), I often throw a mover towels ontop as I have definately replaced rear tint in this due to it getting scratched.... Which got me thinking or over -thinking. Movers towel while not hard is not exactly soft... Do I need to throw a *soft* microfiber towel on it so if it rubs against the back glass, it won't scratch the tint. -
1
What is the best value plotter to cut PPF and window tints?
I just purchased a warehouse to open up a wrap shop to apply PPFs, window tints, and vinyl wraps to customer vehicles. What is the best value plotter to get? I want something that will be reliable, has a really good software that is easy to use and saves film, and something that would break the bank. Ive heard of brands like the Workhorse 2, Graphtec fc9000, and Jaguar V LX 72". What do you guys recommend?! Thank you so much for the help! -
0
Help me pick window tint!
Hi everyone, I need help picking the best window tint for my car. I want to get a ceramic film and have gotten few quotes. Now while comparing them it got me confused. Here are my options listed from most to least expensive. Xpel XR Autobahn Black Ceramic Llumar CTX or 3M Ceramic IR I am looking for perfomance and longevity. -
3
Help me pick?!
Xpel shop has been around for more than 15yrs Llumar and Autobahn one around 4 3m probably around 15+ too. But there was one review questioning the authenticity of film. So staying away from it. So probably out of Xpel, Llumar ans Autobahn -
3
Help me pick?!
High dollar quotes may be representative of; 1) high overhead costs or 2) wanting to stand out in a crowded field through a price illusion of having the best. Most all 'ceramic' films in the industry come within 5 or so percentage points of each other in terms of TSER. The amount of difference is trivial in comparison to overall performance, while occupying the car. Write each one down on a small piece of paper, put them in a bowl, and blindly pick one. Then, get an idea of what their workmanship looks like by visiting their shop, what the product might look like on your vehicle, and what might be their service history rating from online apps. Workmanship outweighs all other factors. I cannot pick for 'you'.
-
