Vauxhall - Opel
30 topics in this forum
-
- 0 replies
- 608 views
Hi guys. I have a Vauxhall (opel) Meriva booked in for tomorrow. I usually remove rear drop glass panels and was wondering if anyone has the de-trim advice for one of these? Thanks in advance.
Last reply by Fresh Tints Derby, -
Anyone done one? Funky looking shape to the rear window?
Last reply by strothow, -
- 0 replies
- 782 views
Anything to look out for? how much of a pain are the rear quarters to do? Thanks!
Last reply by strothow, -
- 0 replies
- 864 views
Easy front doors....5 screws and take off the silver grab handle surround...a couple under that. 1/4 vents a soda. Tape the verticals. Rubber slips out but you have to have the trim off first. Devil
Last reply by Devil with bad attitude, -
Astra h front windows
by Guest Mr.szarvas- 1 reply
- 939 views
Hi everybody, I'm new to tinting. Got an Astra h front windows to do. Do I need to remove door cards & rubbers. And do I need to remove rubbers around the top of the doors. Thanks in advance.. All help much appreciated
Last reply by TintTech Nottingham, -
- 0 replies
- 809 views
How do you guys remove the trim? Been tinting with em on and can't get it clean, new car to me and all brand new so dont want to break shite
Last reply by Thirtyfive, -
- 1 reply
- 1.1k views
Got one in this week. Any tips of things to watch out for. Thanks guys
-
- 20 replies
- 2.2k views
Hello, have one in tomorrow.. Look pretty straight forward but have heard otherwise.. Is the rear at all tricky? Thanks Josh --- I am here: http://maps.google.com/maps?ll=51.922349,-2.167048
Last reply by lewis7942, -
- 7 replies
- 1.8k views
Hey guys, havent actually done one yet, got it in on friday. Just wondering what it's like?
Last reply by tintmor, -
Omega estate 1 2
by Guest dazzer- 12 replies
- 2.7k views
Hi Guys I had a omega estate in today for 5% tints to the rear of the car.I flew through the back doors and side boot windows but could not get the boot window to shrink properley and could not get it right any pointers
Last reply by pulsar2000, -
Vauxhall Vectra 1 piece completed but tiny bubbles! 1 2 3
by Guest Samrasr- 22 replies
- 6.9k views
Did a dry shrink by using Dart filmz, what do you think? I am improving there were some big fingers, Dry shrinked - is this how it should look like once shrinked? Flat with wet check shrink on right side Completed, but small tiny bubbles show Anyway what do you think?
Last reply by The ///Man, -
Vauxhall Agila 1 2
by Guest CheshireTinting- 13 replies
- 3.6k views
Hi Guys, I'm fairly new here, just wondering if any of you have tinted the rear windows on a Vauxhall Agila yet? I notice they're quite new... Any hints / tips? Cheers, Craig
-
Astra Twin Top 2007
by Guest walestint- 3 replies
- 3.2k views
bit of fun that roof half open to be able to reverse roll back window on tight rubber of fronts near door handle, have to trick window up looks sweet done, a light film looks dark on it
-
- 2 replies
- 2.4k views
Hi all, Ive got to do a Astra van front windows (clear security film) just wondered how easy the door cards are to get off ? Any issues with them ? Any information would be great. Thanks
Last reply by s&cautostyle, -
What a car just did one today ,easy car no problems great lookin wagon.
-
2006 vectra hatch
by Guest coolrides- 1 reply
- 2.7k views
got one on saturday, last vauxhall I did penels were hard to remove, any heads up for these rear doors. e.g screw location. cheers
-
- 2 replies
- 2.6k views
HAS ANYONE DONE ONE YET, ANYTHING TO LOOK OUT FOR.GOT ONE TOMORROW. THANKS FOR ANY INFO
Last reply by Tint Artist, -
New Corsa SXi
by Guest TintMeUp- 8 replies
- 4.6k views
what are they like? easy? they look easy, being a newbie I need to know these things lol back quarters look v similar to the old astra, any tips or replies? or will it be fine? thanks!
Last reply by Tint Artist, -
- 8 replies
- 3.4k views
got a mate cavalier to do, has anyone done one - easy/hard. any tips would be apreciated guys
-
how do guys get around the spoiler - I think I'm gonna remove the spoiler or can you do it without removal
Last reply by Pyramids, -
- 4 replies
- 4.8k views
Hi got a Astra made a few weeks ago think it come out nice. without taking the quarters out but I have to cut the 3rd Brakelight out it sucks but thats lawgiven in Germany
-
- 4 replies
- 4.2k views
This is the easiest Tint job on wheels I`ve ever done. all windows with matrix. one side of the car with vinyl stripes around the matrix, tint doublecutted, installed tint . Finished !!!!
Last reply by obi wan folie, -
corsa 1.7 van rear
by Guest walestint- 3 replies
- 3.9k views
did one today, in one peice...... knackered me out that! maybe it was just one of those days ne one else done one of those....how was it?? (dont tell me someones done it is 10 secs)
-
2000 3dr astra
by Guest coolrides- 7 replies
- 3.5k views
anyone done one, easy hard or nightmare?
-
2003 Vauxhall Omega
by Guest graham.god- 4 replies
- 3.3k views
Hi guys.Had one in on friday and had a nightmare!!!Rear door windows are very curvied and need to be shrinked.But after that had HUGE problems getting the film to go behind the felt which line the window runners.Has anyone came across one of these before and got a good finsh?Can the felt be removed?Did ask Autoglass to take the windows out but they said there a nightmare.Any ideas? Cheers Graham
-
new corsa quarters
by Guest walestint- 0 replies
- 2.6k views
hola are they similar to the astra mk4 rear door quarters by any chance?
-
VAUXHALL astra mk 3/opel kadett mk3
by Guest fimmo- 2 replies
- 6.3k views
watch this car!!! 3 door isnt too bad,bit off work but the 5 door is very hard! basically,like the new bug you have to shrink every window!!! dont know why vauxhall/opel made the windows as bad as they are,the felt covered rubber seals around the door are a nightmare, you have to remove it,it grips the glass so tightly your tint WILL NOT go between,remove it then wash down to remove all traces of the felt! hope this helps!
-
Tigra convertible
by Guest vampire- 1 reply
- 4k views
New tigra from vauxhall (opel) in the us, How do you get to the rear glass.
-
Search Rear Spoiler for Corsa B
by Guest German Corsa 16V- 0 replies
- 4k views
Hello. I comes from Germany and searches nen pair spoiler which I my Corsa 1.6 16V cultivate on can. since I do not find however in the InterNet the spoilers you I search wanted I you times to ask whether their me further help could. Look for these spoilers in the pictures are.
-
opel kadett mk3
by Guest fimmo- 0 replies
- 3.7k views
see my post at the bottom of the makes and models page describing the vauxhall astra mk3 as these cars are the same just badged different!
-
Sponsored by
.png)
-
Activity Stream
-
4
Low angle haze
Im not that worried about brand recognition. Ive been getting work with Avery and its got little to no brand recognition as far as tint goes. I'm just looking for a good brand that I wont have an issue with. Avery is a fairly cheap option as far as Im aware, so I'm just getting ready to move into the big leagues with a more premium brand. Ive used STek's tint and I was pretty happy with the way it looked, shrank and the overall experience with customer service has been great too. I stopped using it because their specs feel like they are below par compared to the other premium brands. Specifically their TSER. Their NEX line seems to be compared to Xpel Prime XR Plus, but the specs were more on the line of Prime XR. Anyone know how that TSER number is calculated? Is it just a calculation combining light rejected, transmitted, reflected, etc? Looking into panaplex, autobahn, and global now. More specifically global because of recommendations. -
4
Low angle haze
I second the Global suggestion. If you can get past the color(khaki) of the 70% ceramic, it is the best performing film in their line. It has amazing heat rejection properties at a 70% film with very little low angle haze. I don't have anyone complain about it. If you install 50% on windshields then you will LOVE the Global 50% ceramic. One of the prettiest films i've dealt with and I would say "almost" zero low angle haze. It does not perform as well as the 70% in my opinion because they have almost the same "stats". @Dano Hang in there with the brand recognition. Just spit your knowledge and let them look it up if they want too. Global is my favorite of the "big 3" and the recognition is getting out there. -
0
Best place to learn window tint ppf
I am currently in the process of getting my detail business going in northern Alabama, and I feel that being able to add tint and ppf, would be a great addition and separate me from some other businesses. I have found a lot of these 2 day work shops, they range from 1 to 5 days, are any of them any good? I would assume the Xpel training etc would be quality, but I was hoping to find something a bit closer to home. I have no issue traveling but if I can find it here or like near Atlanta it would be a lot more convient. Any info on any of these class workshops would be appreciated, and if u got an idea I've overlooked. Let me know that as well,. Thx for the help fellas -
4
Low angle haze
I've had good results with the Global so far. No minimum requirements but also not much brand recognition in my area. -
4
Low angle haze
Basically, the technology that is blocking the heat is also creating the low-angle haze. Some films are worse than others, but they all have it. We've only had 2-3 customers complain about it in the last 10 years. So not a major issue at least for us.- 1
-
-
4
Low angle haze
I have been using Avery Dennison's NR Nano Ceramic IR but I keep seeing cloudy results or low-angle haze. I think some haze is acceptable as a trade-off for performance, but there are just some customers who may not be happy with the result. Does anyone know of a tint manufacturer that has little to no low-angle haze? Preferably one without a $10k minimum monthly buy-in or something crazy like that. Does this only affect ceramic tint? -
0
HIRING INSTALLERS - full time positions Vinyl Graphic Installers
Full-time vinyl graphics installer positions available. Please apply on our career site if interested: Careers - Adsposure | Advertising Vehicles Or contact mclayton@EST03.com via email for more information. Current location needs: -Cincinnati, Ohio -Chicago, Illinois -
0
Colorado Tint & PPF installer(s) needed!
We are a business with many different dealer accounts all throughout the Denver area and we are in need of another installer or two. We need guys with experience that are dependable, have an eye for detail & are capable of turning out high quality work. Unfortunately we are not looking to hire/train someone with little to no experience at this time. At the very least, we need someone who's capable & comfortable with doing basic 18" Clear Bra's (Hood, Fenders, Mirrors, Door edge/Door Cups) as well as 2 window match/full tints by themselves. There is plenty of work for at least 1 possibly 2 full time installers and the pay is good. To talk details or for more info please feel free to reach out and we can discuss further/set up an interview. 720-938-6822 Noah.shepard18@gmail.com -
0
Tinter looking to relocate
20+year experience tinter and 12 volt installation looking to relocate farther south drug free dependable and used to fast pace working environment my profile is on indeed with qualifications and resume also available upon request feel free to contact me with any questions 865-409-8966- 20+years experience
- management experience
- (and 1 more)
-
-
