Jaguar
48 topics in this forum
-
Jaguar x type 1 2 3
by Guest dustedu5- 27 replies
- 11.2k views
Hi Im having a horrible time getting my rear window tinted because the deck on my jaguar x type 04 is to close to the window, is there any way I can remove that myself?
Last reply by Devil with bad attitude, -
Jaguar XF 2008 1 2
by Guest simon weekes- 15 replies
- 8.9k views
Hi Has anyone tinted the new XF Jag? The rear brake light is built into the rear, at first look I think I am going to take out rear seats and trim? Plaese help
Last reply by VIP tint + glass, -
2004 JAGUAR TYPE-S 1 2
by Mdog- 13 replies
- 6.5k views
the doors have rubber gaskets along the sides and the bottom seals are very soft and easily tucked. the backglass on the other hand is pretty curved, reminded me alot like shrinking the new style lincoln town car backglass, because of the amount of shrinking you have to do.
Last reply by mustangdroptop96, -
- 7 replies
- 6.4k views
Rear deck on these is right against the glass. Too tight and fuzzy to leave in. Fold the rear seats down using the release in the trunk. To remove the back seat side panels slide your hand in on the left side of each panel. (inside of driver's side, outside of pass. side) Push in the clip at the bottom of the plastic anchor. (in the first picture) Then the panel pulls out enough to gain access to side bolts that hold on the deck. Then remove the bolts anchoring the child seat belt attachments. The side pillar panels pop off from the top and pull up and out. The clip I'm holding out (in the second picture) slides up and out for panel removal. It's kind of a ti…
-
2005 S-Type 1 2
by blade- 11 replies
- 5.7k views
Very easy car to tint. Seals tuck easily. No need to pull panels. Although they do come off pretty easy. No need for deck removal. Jammer is enough to get behind the brake light. Alittle too tight for the bulldozer though. What's with all these new cars? Leave the key on for 20 minutes and the battery is dead. pieces of crap Might as well stick a charger on the battery while working on it. And the battery is in the trunk underneath the floorboard that folds up.
Last reply by hooli, -
- 6 replies
- 5.5k views
I had a 2013 XJ-L last week which was impossible to get the headrests out and also could not get the seatback out for nothing. The brake light was so tight to the glass that water wouldn't even pass it, unless pushing down on it, in which it maybe moved an 1/8". Ended up cutting around that one. No light gaps but hate having the short-cut look on the outside. If any one knows how to get the seat back out of it so the deck can come out please reply. There's bound to be another one pulling in one day. This car didnt have a fold down seat appearance like the XF in my other recent post, which also didnt fold down without manually tripping the hidden latches. I successfully …
Last reply by Naples Tint Company, -
Jaguar XJR
by Guest Eclipseohio- 9 replies
- 5.3k views
Ilike the XJR, But for about 75,000 or so you could get a much nicer car. The BMW 745 (which most people complain about the hand controls) seems the better buy. I recently tinted Ken Griffey Jr.'s XJR which would be the first one I've driven. I've tinted probably 10-12 745's, so yes I've been in more of those, but they seem to be laid out alittle better in my opinion. This would be my first post so I like to say hi to everyone. I have been tinting for 8 years and in the business for almost 12. Any questions you can contact me.
-
98 Jaguar XK8 Convertible
by Guest Kelly's- 4 replies
- 4.9k views
Customer just pulled in with a 98 Jag XK8. When I hit the switch for the top to go down the rear quarter windows also go down. There doesn't seem to be a way to get just the rear quarters by themselves to go up. Any suggestions?
-
- 8 replies
- 4.6k views
Did 2 this week, doors are about as hard as the new BMW 7 but the PITA is the back glass. Third brake light is right up against the glass, but if you push on it you can just fit your Bulldozer in.
Last reply by jlmontec, -
S-type
by Guest tintmax- 3 replies
- 4.6k views
Any tips on doing a 2002 s-Type. Looks to be fairly cut and dry.
-
2011 Jaguar XF
by Guest perfectdark- 6 replies
- 4.5k views
I know the back window of the new Jaguar XF might be a bit tricky only because the centre brake light in the rear tray bulges out close enough to touch the glass. has anyone ever removed that rear tray? if so please let me know how youve done that, I'd hate to have to cut the brake light out of the window film. Thanks!
Last reply by evowrap, -
98 XJ6
by Guest thetintshop- 6 replies
- 4.5k views
got one coming this morning, anything I need to watch out for?
-
- 2 replies
- 4.2k views
There was a post with instructions on how to remove the rear deck on this generation-Just so you know, the rear seat on the 2012 I just did didn't have release cables to fold it down as some others. These have a very tight brake light, and hard plastic trim touching the bottom of the rear glass along the matrix so i wanted to remove the deck for a flawless install and no cutout. I looked in the owners manual and it clearly showed where to pull the releases, with no noted exceptions, but they weren't there. I searched some Jag forums and found out that starting in Model year 2012 only the XF-R is equipped with fold down. I was able to locate the latches, in the truck, at t…
Last reply by NvrLate, -
2010 Jaguar XKR?? 1 2
by Guest Tintkang- 11 replies
- 3.7k views
has anyone done this car yet? I have one coming tomorrow morning, and was wondering how the back window is. since its a 2 door, im afraid it might be kind of tight down in there.
Last reply by VIP tint + glass, -
- 3 replies
- 3.7k views
The back glass isn't laminated...9 windows...no space to work, no border. Can't remove any window...Somebody have an idea how $$$...may be 6-8hrs to get it done perfectly..?
-
oil filters
by Guest kedia_82- 3 replies
- 3.7k views
the other day I went to the auto fair where there was a kiosk of NAPA and they had their products lined up and the one produck that got my eye was the spin flow oil filter selected by NASCAR. it looked great and had a lot of advantages ovet the old one which I use now. I checked up there site as well <snip> and was wondering if any of u guys have tried it , pleas let me know abt it as I want a new oil filter. and they also have a contest on the website where u get the results immediately and can win loads of stuff. so just check that out too. <snip>
-
- 2 replies
- 3.6k views
Any tips on one of these? Basically I want to know if I should be scared? I heard it was one of these... and I cringed. Thanks for any help guys. Rich
Last reply by Underground, -
- 4 replies
- 3.6k views
I am doing an R&R (crap part about gettin better than the others around here!) and this car will prob need the tray removed for cleaning purposes alone. The rear seats do not fold down like the 03 models. I am wondering if anyone knows how to get these suckers out. The thing is drivin me up the wall.
-
98 XK8 conv.
by Guest expertint- 1 reply
- 3.3k views
We just did one and the locks broke where he can lock it at the dr door but pass door doesn't lock from the dr.side..also when you put the conv top down the windows roll down...any tips??? The rear rollups are a real pain.
-
@003 Xtype Jag
by Guest expertint- 0 replies
- 3.3k views
Got one here pkg tray up against the glass////rear seats fold down and side bottom seatpanels have a clip on them that you push towards the outside..panel then comes off but seatbelts won't come thru the tray.We just pulled it forward and will tint around it.kinda fuzzy.
-
- 1 reply
- 3.2k views
If you leave the key on too long it screws the computer system up. The car wont start at all. It will sound like the battery is dead. what you need to do to fix it is this. turn the key to the on position and try to put the car in gear. It wont go in gear but you will see the light of the s button turn red. When that light goes on you then need to turn the key while it is still light to start the car. you then have to let the car run for 20 mins. Because it still will be messed up the car will not go into gear. after the car runs for 20 mins turn the key off and wait thirty seconds. then start the car again like usual and all should be fine. hard to beleive you have to g…
-
'91 XJ6
by Guest 2dark2C- 1 reply
- 3.2k views
I have a 1991 XJ6 coming in this weekend and I have never done one, is there any tips anyone has on this car that will help me out?? THANKS!
Last reply by TintWizard, -
r&r on '06 Jag XJ8?
by Guest WISEGUYSinc- 6 replies
- 3k views
I need someones advice. I have this '06 Jag XJ8 here. The lady that dropped it off wants an R&R for the back glass. She just purchased the car, and said she thinks the film is causing the AM Radio to be a li'l fuzzy. She pointed out the 3 antenna lines above the defroster lines at the top of the back glass. So while driving it around to the garage I turned on the radio and the AM seems fine.. I mean just a little bit fuzzy but AM usually is. The FM sounded like HD radio, real clear. It seems like the AM is fine to me. What are some of you guys's take on this. Opinions are appreciated.
Last reply by Pyramids, -
2006 XK Coupe
by Guest Rockabilly- 1 reply
- 3k views
Door trims dont need to be removed. There is a plastic end cap on the door trim which pops off to reveal a screw. Take out this screw, and the top of the door panel can be pulled away from the door, and the rubber gasket comes out easy. The little quarter glass windows look harder than they really are, the rubber is soft and you can slide the tint in behind it for a clean looking install. Tried to remove the rubber totally, and even asked the Jag techs what we should do, but we tried it as-is and got a good result regardless. Rear window is a hatchback.
-
1986 Jag XJ6.....Gasket window?
by Guest darkdan- 2 replies
- 2.8k views
I'm 90% sure the rear window is a gasket window with no painted border. Can anyone confirm either way?
-
- 4 replies
- 2.8k views
Anything to look for? PS I am not a panel puller, nor do I want to pull the rear deck.
Last reply by TINTZEUS, -
- 5 replies
- 2.7k views
Had one to do today and could not get the 1/4's to stay up when the top went down. It would be good if I could find a fuse or something to pull that controls these little buggers. They have no frame around them and it would look a whole lot better if I could tint them to the edge. Any help would be appreciated. Thanks
Last reply by isaiahdrums, -
98 XJR
by Guest obxtint- 2 replies
- 2.7k views
I've got one on friday. Any tips? Panel removal? Rear deck? easy Shrinker? How tight is the rear rubber to the glass? like jeep cherokee tight?
-
- 8 replies
- 2.7k views
had a customer ask me to tint this car , told him i would have to get back to him , any issues i need to know about , how difficult is it ,
Last reply by matty cox, -
- 4 replies
- 2.5k views
this car is georgous! doors simple,rear light ON the rear glass. yeh its supercharged!
Last reply by blackout66, -
- 4 replies
- 2.1k views
Never done a jaguar before. Anything I should be aware of? Plus I pull sweeps so do I have to pull whole door panel? Thanks
Last reply by jayson3st, -
- 0 replies
- 2k views
Reach under the lower seat cushion to release. There will be several connectors to disconnect. Pull the 2 straps coming out from under the top section. Seat will tilt forward and pull out. You will have to remove all the side trim panels including the lower door jamb pieces. There will be 2 8 mm bolts holding the deck in on each side plus 3 clips at the front. Just loosen the bolts, you won't have to remove them all the way. You can see the black tabs on the bottom side of the deck.
Last reply by tint-factory clearbra, -
2002 XKR Coupe
by Guest shadowline- 2 replies
- 2k views
As per the title any issues, I know its a framless door, but is there any need to pull the panal, I seem to recall an issue of people saying its hard to get down below one of the weatherstrips? Any helpers? Also what size roll for the back glass?? Rear deck brakelight ok to slide behind? cant see any around to have a measure for the rear glass, Cheers Guys
-
- 7 replies
- 1.9k views
Hey guys, i have a 2016 XE sedan booked in tomorrow, normally i pop or pull panels. Is there anything i need to be careful with? also will a hybrid metalised film be alright on rear window for antenna? my films are normally good for am and fm radio on other cars. anyone got links to pics of vids of door trim removal ? i will take photos as i go of anything i need to pull apart and i will update this thread but id love to see what im up against before i go poking around expensive trims Post Update- I popped the tops of trims back and masked up the felt for the doors, back window does not give a whole lot of space inside the car as window is on a big slope so i …
Last reply by Derny311, -
- 7 replies
- 1.9k views
Just took delivery on the car and have to have it done overnight, I read the few posts on it and have a few questions How do you get the rear deck out? I am not seeing any typical ford clips for the bottom of the seat and am not seeing any hidden pull for the rear seats to fold down. So any tips or walkthroughs on removing the rear deck would be great. Also. Bottom sweeps on side doors look like a nightmare, I'm normally a panel puller but is there any tricks? If all else fails, i just tint the 1/4 rear windows thank you
-
- 2 replies
- 1.6k views
I tinted one of these a couple months ago (2019 I believe). Did not remove the rear deck, headrests or pull any panels so it was definitely a little more challenging than your typical sedans. Overall it came out nice. The doors are tight so I cut almost exact with hardly any shifting. The rear window was the most challenging. I have done a handful in the past and have always cut around the brake light. This one happened to be for a Steeler player so I decided to go for it without cutting it out. It came out clean but in order to squeegee behind the light I had to press down on the deck lid while using the bulldozer. This particular one gave me just enough room for me to …
Last reply by 1 Touch Tint, -
- 6 replies
- 1.5k views
Be ready to pull a spoiler if you can't plot back window, doors are easy w sweeps removed, comes apart like a Bmw 1 t20 on back edge of door panel behind a very noticeable cover. Sweeps almost fall out
Last reply by pbalentine, -
2007 Jaguar XKR
by Guest Chris91Z28- 2 replies
- 1.5k views
Pretty easy car overall. The rear wing windows were a little difficult, but that was it. Doors and rear hatch window were cake. Nice ride.
Last reply by tintpro, -
2013 XF
by Guest Mo Evo- 2 replies
- 1.3k views
I don't tint a lot of Jags, so I have no idea what to expect. Can anyone give me tips or a heads up on this car?
Last reply by TTS, -
- 1 reply
- 1.2k views
Anyone done the new XFR? Water issues? We dont pull anything was just curious if any weird stuff to know about for tomorrow.
Last reply by TintOhio,