Jump to content

felt n rear quaters

Guest walestint

By Guest walestint
in Window Tinting - General Discussion

Recommended Posts

Guest walestint

Guest walestint

Posted
Posted

Had two pretty harsh felt on rear roll down and quarter experiences of late ...

as regards getting a pucker finish ...

seat leon and new shape astra 5 dr's ...

contamination drifting from felt :lol6 ....

only solution I can come up with is push the car out of my unit :rollin

they just take up quite a bit of time and patience in relation to pee easy rears etc

any advice on the fkin felt as me 'no likin de felt' over last two weeks

might be the weather :lol6

then again 'thats tintin for ya'

:lol6

Link to comment
Share on other sites
Guest walestint

Guest walestint

Posted
Posted
English please

tis ok

just seen a posting on tips of week or something like that

got a bit 'heated' over the use of a blow torch

no 'blowing' in my unit

:rollin

Link to comment
Share on other sites
Guest potzy

Guest potzy

Posted
Posted

English please

tis ok

just seen a posting on tips of week or something like that

got a bit 'heated' over the use of a blow torch

no 'blowing' in my unit

:lol6

Yep, hot air works wounders on them felts mate... :rollin

... Im down your way this weekend using your local race circuit at Pembrey dialling in my

GSXR, pop down if your at a lose end on saturday :lol6

English please

Hey rick, wada mean, it is english :lol2:lol6

Link to comment
Share on other sites
Guest Diamond Tints

Guest Diamond Tints

Posted
Posted

On the new shape astra 5 door if you just strip the quarters out them then just take the drop glass out at the same time this would give you a nice clean install :rollin

Link to comment
Share on other sites
Guest tintdeck

Guest tintdeck

Posted
Posted
Had two pretty harsh felt on rear roll down and quarter experiences of late ...

as regards getting a pucker finish ...

seat leon and new shape astra 5 dr's ...

contamination drifting from felt :lol6 ....

only solution I can come up with is push the car out of my unit :lol6

they just take up quite a bit of time and patience in relation to pee easy rears etc

any advice on the fkin felt as me 'no likin de felt' over last two weeks

might be the weather :lol6

then again 'thats tintin for ya'

:rollin

try masking all felt then cleaning down the sides with damp vibto cloth round your hard card works great on the audis

Link to comment
Share on other sites
Guest walestint

Guest walestint

Posted
Posted

English please

tis ok

just seen a posting on tips of week or something like that

got a bit 'heated' over the use of a blow torch

no 'blowing' in my unit

:dmc

Yep, hot air works wounders on them felts mate... :bs

... Im down your way this weekend using your local race circuit at Pembrey dialling in my

GSXR, pop down if your at a lose end on saturday :thumb

Missus is due to drop in next few weeks so we are getting ready for that, decorating etc! Pembrey is about 50 miles from me, im further west still

but would be good to catch up with fellow tinters one day!!

:dmc

Had two pretty harsh felt on rear roll down and quarter experiences of late ...

as regards getting a pucker finish ...

seat leon and new shape astra 5 dr's ...

contamination drifting from felt :bs ....

only solution I can come up with is push the car out of my unit :bs

they just take up quite a bit of time and patience in relation to pee easy rears etc

any advice on the fkin felt as me 'no likin de felt' over last two weeks

might be the weather :dmc

then again 'thats tintin for ya'

:dmc

THANKS FOR ALL THE TIPS FOLKS ............ :lol

Link to comment
Share on other sites
Guest potzy

Guest potzy

Posted
Posted

:thumb

English please

tis ok

just seen a posting on tips of week or something like that

got a bit 'heated' over the use of a blow torch

no 'blowing' in my unit

:hmmm

Yep, hot air works wounders on them felts mate... :DD

... Im down your way this weekend using your local race circuit at Pembrey dialling in my

GSXR, pop down if your at a lose end on saturday :thumb

Missus is due to drop in next few weeks so we are getting ready for that, decorating etc! Pembrey is about 50 miles from me, im further west still

but would be good to catch up with fellow tinters one day!!

:bat

Had two pretty harsh felt on rear roll down and quarter experiences of late ...

as regards getting a pucker finish ...

seat leon and new shape astra 5 dr's ...

contamination drifting from felt :wall ....

only solution I can come up with is push the car out of my unit :lol

they just take up quite a bit of time and patience in relation to pee easy rears etc

any advice on the fkin felt as me 'no likin de felt' over last two weeks

might be the weather :bingo

then again 'thats tintin for ya'

:dunno

THANKS FOR ALL THE TIPS FOLKS ............ :beer

no problem mate

No problem mate, best of luck with the baby stuff :thumb

HAHAHA. wuussuup potzy.

Things are hectic at work mate, but still got time to squeeze the bike stuff in though. :hmmm

Link to comment
Share on other sites
Guest 1PEECBARETTA

Guest 1PEECBARETTA

Posted
Posted

I found a nearly brand new gsxr1000 very very cheap potzy. send me some cash and I will ship it to you!

After I make sure it's in good order and race it a few times.cheers

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

Go to topic listing
  •   Sponsored by
    autocut-tech

    tinttek

    filmvinyldesigns

    ride wrap

    Lexen

    tintwiz

    signwarehouse

    martinmetalwork.com

  • Activity Stream

    1. 1

      My summa plotter wont connect to my computer even tho i have all plugs plugged in

      I sometimes have problems with my plotter not cutting or even my program not detecting my plotter. When this happens, I go to system, device manager, Ports (Com & LPT) You should be able to see your plotter listed and the Com port it is associated with. Make sure your cutting program is pointing to the same device and Com port in the program's setup area. I usually end up sorting things out eventually. Other than this, I have no other advice as I'm just a novice computer tech 😬
      doctor4766 in Summa
    2. 1

      My summa plotter wont connect to my computer even tho i have all plugs plugged in

      Im having a lot of trouble with conecting my summa plotter to my laptop. I have multiple plugs going from my plotter to my laptop and everytime i open a sofware for ppf and tint templates it says no plotter detected even tho the software is telling me that is has cut the templates but the plotter didnt cut. If anyone could help that would amazing, ive been stuck on this for over 2 weeks and i cant find anything online
      thats a wrap in Summa
    3. 0

      Problems conecting my summa T1400 SL to my laptop

      Im having a lot of trouble with conecting my summa plotter to my laptop. I have multiple plugs going from my plotter to my laptop and everytime i open a sofware for ppf and tint templates it says no plotter detected even tho the software is telling me that is has cut the templates but the plotter didnt cut. If anyone could help that would amazing, ive been stuck on this for over 2 weeks and i cant find anything online
      thats a wrap in Plotters and Cutting Systems
    4. 2

      Windshield protective Film

      Me too. Contact me for the address to send samples to. tinttech@optusnet.com.au
      doctor4766 in Paint Protection Film, Clear Bra Forum
    5. 0

      Flat Glass Installer Pay

      I have a new residential/commercial flat glass business and want to hire an experienced installer who is very good. What would be an competitive rate to pay someone by the Sq Ft assuming they are experienced, professional and motivated?
      333filmguy777 in Window Tinting - General Discussion
    6. 2

      Help me tint my living room windows

      Blinds/curtains will be the best route. You would have to add a dark window film to reduce the sun a good amount but not eliminate it. Anything darker will be extremely noticeable from the outside. Anything lighter will not be drastic enough to make a difference.
      DynamicATL in Window Tinting - General Discussion
    7. 2

      Vinyl Express Q series help

      Thank you
      Tintchick in Vinyl Express
    8. 2

      Help me tint my living room windows

      I have a living room with windows on the east and south and knowing what I know about the effectiveness of even the darkest film, which comes with hazards of thermo stress on the dual pane glass ... I set the TV in the corner between the two windows. Viewing the TV and the windows in the same field of vision. There will always be a reflection of the windows on the TV, just muted. Curtains are the best solution for this issue.
      Tintguy1980 in Window Tinting - General Discussion
    9. 0

      Mutoh cutter

      Anyone using a Mutoh valuecut-2 for cutting tint? I have one that I use for vinyl and plan on buying another cutter just for tint if it will work. Looking to stay with the Mutoh as I am familiar with it. Thanks
      Hookedup in Window Tinting - General Discussion
    10. 2

      Help me tint my living room windows

      I live in a second story apartment and there are two windows in my living room, one facing east and one facing north. My TV is against the wall facing left and my couch is against the north wall right next to the window. In the late morning and early afternoon the sun shines through the east window and casts an annoying reflection on my TV, and sometime around 1 or 2 pm every day the sun gets right in my eyes when I am sittin or lying on my couch even when I am facing the TV. I want to cover these windows with just the right film for solving all of these problems while also making it not look obvious that I tinted them, and I'm not sure what kind I should use because apparently different brands will have different results even if it's the same percentage, could someone help me out here
      DaneClark in Window Tinting - General Discussion
×
×
  • Create New...