Jump to content

Inside grids on doors

Guest LukeNukem

By Guest LukeNukem
in Window Tinting - General Discussion

Recommended Posts

Guest LukeNukem

Guest LukeNukem

Posted
Posted

I did some french doors today that had grids on the inside, I was going to just do 15 small cut and trims but decided to pop the plastic plugs and unscrew the grid frame. I used 2 or 3 scrap pieces on each door rather than cut all the littles ones. Looks better and I think its a lot quicker too.

Link to comment
Share on other sites
Guest VOLTRON

Guest VOLTRON

Posted
Posted

get some L shaped tabs like they use to hold on solarscreens and put one at the top of both sides and the bottom of both sides. Take the screws that hold on the plastic frames and use them to screw through the L shped bracket and back into the holes they came out of.

Link to comment
Share on other sites
Guest LukeNukem

Guest LukeNukem

Posted
Posted
get some L shaped tabs like they use to hold on solarscreens and put one at the top of both sides and the bottom of both sides. Take the screws that hold on the plastic frames and use them to screw through the L shped bracket and back into the holes they came out of.

I was actually thinking of a trick like that today but the window was painted in pretty well from the outside, although I did find myself squeeging with one had and holding the other outside just to be safe.

Link to comment
Share on other sites
Guest vclimber

Guest vclimber

Posted
Posted

get some L shaped tabs like they use to hold on solarscreens and put one at the top of both sides and the bottom of both sides. Take the screws that hold on the plastic frames and use them to screw through the L shped bracket and back into the holes they came out of.

I was actually thinking of a trick like that today but the window was painted in pretty well from the outside, although I did find myself squeeging with one had and holding the other outside just to be safe.

:beer I thought I was the only one around here doing that. :beer

See VO|TRON, I'm not the only one... :beer

Link to comment
Share on other sites
Roach

Roach

Posted
Posted

I had a thread going at one time on these types of doors... Way cleaner look to pop the grid off. I just make sure I tell the customer what the dillio is... caps - easy. If the screws are covered with putty or something it's going to be a mess, but the end result is much nicer. Never had anyone ask me not to take it off...

RoAcH

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

Go to topic listing
  •   Sponsored by
    tintwiz

    signwarehouse

    tinttek

    martinmetalwork.com

    filmvinyldesigns

    ride wrap

  • Activity Stream

    1. 1

      3M ceramic ir vs. LLumar Pinnacle

      Go with the shop you feel will give you the best installation/service. Both films are high-quality, and performance is on the same level. So either way, you can't lose. If you go with 3M CMIR 35%, have the shop confirm it will meter legal. Depending on the % of your stock glass, it could vary by 1-2%, which could be enough to meter too low. Personally, I love 3M CMIR as it is a great-looking film. Except for one, every vehicle in my family has it installed.
      DynamicATL in Window Tinting - General Discussion
    2. 1

      3M ceramic ir vs. LLumar Pinnacle

      Hello! I am looking to get all of my windows tinted (minus the windshield) in my Mazda CX-5. I got a few quotes from some shops and need to decide which one to get. Shop 1: $419 ceramic ir Shop 2: $480 for LLumar F1 Pinnacle I would prefer the LLumar one, as it is 40% and not 35% like the ceramic ir due to me having to pass inspections in NC. I have also heard that LLumar tends to be better quality, but some people swear by 3M. I think it’s mainly preference, but correct me if I’m wrong. On paper the 3M looks better, but the shop that is selling LLumar says theirs is slightly better so I could be looking at the wrong numbers. They also sell the CTX for $420, but that’s worse than the 3M ceramic ir. Help me decide lol.
      Raleighman223 in Window Tinting - General Discussion
    3. 1

      XPEL WINDOW TINT shrinking

      It happens from time to time, usually when you don't have enough soap or there's a spot that's not quite dry and the film grabs the glass. It's super easy to crease when that happens, I usually just lift it and let it settle back down to reset and then continue on. Gotta be careful not to overshrink it too.
      highplains in Window Tinting - General Discussion
    4. 10,324

      The Off Topic Thread

      Evening everyone It's been daily monsoons up here, really makes me wonder what the rest of the summer is going to be like Y'all are scaring me with this shit, I'm still in my mid/late 30's and already have a hell of a time in the morning
      highplains in Off Topic
    5. 0

      Now Hiring experienced Tinters and Wrap Techs In the heart of Atlanta.

      Great Pay and busy location. Contact Mike at 678-245-0748. I am also looking for a tint instructor with over 8 years of experience. I look forward to hearing from you. Come join the winning team.
      Mike Cutt in Classifieds • Employment • Marketplace
    6. 1

      IR Specs

      There are people way smarter than me but I'll sling a guess out there that what you are experiencing is the difference between IR and R factors. Window tint blocks(absorbs/reflects) UV and IR parts of the heat spectrum, BUT window tint does not have an " R factor " like the pink stuff in your attic. It takes mass to create an " R " factor. The shade is designed to reduce heat and also has the mass to create more of R factor in heat rejection and I am assuming that is the difference you are feeling.
      Bham in Window Tinting - General Discussion
    7. 1

      IR Specs

      Rear glass comes factory dyed. It has XR Plus 70% on it In looking at the IR specs... 92 vs 97% etc, not much of a differential of 5% Riddle me this Sitting in the backseat - I raised up the rear window shade. I did feel a difference in -less- heat with the window shade. The window shade is not solid but is semi perforated ? Is it due to an extra -layer- past the window. It wasn't on my radar as it does reduce the -feel of heat- from the sun shining on the window. Here I was thinking the IR 92% was a pretty decent spec in itself but the rear shade does add (less heat feel) for sure. I'm sure someone on TD has a better technical answer for my WIKI
      mobiledynamics in Window Tinting - General Discussion
    8. 10,324

      The Off Topic Thread

      I hear ya bro.
      TintDude in Off Topic
    9. 10,324

      The Off Topic Thread

      Feeling it today. That getting old thing hitting hard. Love sleeping but hate waking up. Hurts to wake up. Plantar Fasciitis is really bad today. Hurts to walk around on this hard floor.
      Bham in Off Topic
    10. 10,324

      The Off Topic Thread

      Howdy
      TintDude in Off Topic
×
×
  • Create New...