Jump to content

Vauxhall Vectra 1 piece completed but tiny bubbles!

Guest Samrasr

By Guest Samrasr
in Vauxhall - Opel

Recommended Posts

Guest Samrasr

Guest Samrasr

Posted
Posted

Did a dry shrink by using Dart filmz, what do you think? I am improving there were some big fingers,

Fingerswhendry.jpg

Dry shrinked - is this how it should look like once shrinked?

Shrinkedindry.jpg

Flat with wet check shrink on right side

Shrinkedwetfromdry.jpg

Completed, but small tiny bubbles show :mad

Vectrafinished.jpg

Anyway what do you think?

Link to comment
Share on other sites
  • Replies 22
  • Created
  • Last Reply
Fiveofeen

Fiveofeen

Posted
Posted

dude, I think I see baby powder... dump that stuff an git wit the MDOG soap shrink mang!

You def got shrinkin down, the install doesnt look bad... keep pluggin as willie says mang!

Look into the soap shrink its that important. Its all over dis place like a mug.

Link to comment
Share on other sites
Guest Samrasr

Guest Samrasr

Posted
Posted

Cheers dude, can I use any soap?

So clean the window outside and then use soap over the window, make a H anchor and then apply film locking the sides.

Is this right? What makes it so different to the powder methood?

Link to comment
Share on other sites
Fiveofeen

Fiveofeen

Posted
Posted
Cheers dude, can I use any soap?

So clean the window outside and then use soap over the window, make a H anchor and then apply film locking the sides.

Is this right? What makes it so different to the powder methood?

well for one the car and the tint aint covered in damn baby powder!

Ivory soap is my fav, I put it in a sock (also handy for beatin mehicans) wet the rear glass, apply a layer of soap (I try to keep it on the drier side) wait for the glass to be 100% dry, lay your film anchor it and start shrinking. It allows you to hit much larger areas quickly instead of the large fingers you see in your 1st picture. Its more of a "surface shrink" I did it forever too wet and then let it really dry out once. It shrinks quickly and there is no mess, a bar of soap lasts ages too. Also remember handy for beatin mehicans :mad

Link to comment
Share on other sites
Guest Diamond Tints

Guest Diamond Tints

Posted
Posted
Good job..man

Good job :mad f**k seeing your tint work, sorry man but it looks crap full of dust and waaaaaaaayyyy too much powder on there also :mad

Try tinting indoors for a better result :mad

Link to comment
Share on other sites
Guest naughtydog

Guest naughtydog

Posted
Posted
Good job :mad f**k seeing your tint work, sorry man but it looks crap full of dust and waaaaaaaayyyy too much powder on there also :mad

Try tinting indoors for a better result :beer

:mad:mad:beer

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

Go to topic listing
  •   Sponsored by
    tintwiz

    auto-precut.com

    signwarehouse

    martinmetalwork.com

    tinttek

    filmvinyldesigns

    ride wrap

    Conco

    Lexen

  • Activity Stream

    1. 7

      Removable rigid window tint sheets - WTF?

      I created an account just to respond here. I'm not a "tinter" or whatever yall may call yourselves but I came across this product and thought that it looked pretty cool and something I could do myself. I ordered from Lazeway and spent like $150 for two packages. The product is from China although they claim all this America stuff on the website. All i received was two simple rolls of tint, nothing special. I was totally scammed and now I'm looking all over the internet for anyone talking about this product to let them know. Dont buy from them.
      Mario L in Window Tinting - General Discussion
    2. 7

      Air80 vs Stratos70 Windshield

      Since there is no limit of darkness on the top strip, I have wanted to tint it. But I would go very dark, to help with sun glare in the evening.
      mikenot in Window Tinting - General Discussion
    3. 7

      Air80 vs Stratos70 Windshield

      Yeah that’s a very fair point to a degree I’m probably overthinking it. I don’t see really significant glare reduction until you get into much darker tint. Like you I think visibility for me is more important living in the country. I’ll probably see what the specs list the differences between 70% and 80% and then double check with the tinter as to what they recommend. Likely will end up with 70% with a strip along the top. Air80 seems to be much more popular, not sure if it’s due to performance or the difference in cost being so much more for the stratos. thank you
      joshiemcduck in Window Tinting - General Discussion
    4. 0

      Process

      Hey guys - so I work for a vinyl graphics company that is adding window tinting to their repertoire and I had a question about your guys' ideal process. I have my plotter set up and my window tinting software ready to go, but I am completely ignorant about the way that tint installers prefer that things be cut. Currently, I will plot/weed the tint and cut the backing away as much as I dare before handing it over to the installer. I was thinking that the installer would prefer the tint to be cut to shape which I believe I can achieve with the perf cut on my plotter. Is that the typical process or should I not be worried so much about it being cut to exact shape?
      DonMeads in Plotters and Cutting Systems
    5. 7

      Air80 vs Stratos70 Windshield

      Im in TX, plenty of of what you mentioned. While I do sit higher in an SUV, glare reduction is not improved much at all with what I have. My 80% is almost clear, not dark at all. With all tint, it adds a bit of reflectivity from the outside, which I notice makes it slightly harder to see from the outside looking in, in the form of a glare not darkness. At the end of the day, it's not permanent, it's only money!
      mikenot in Window Tinting - General Discussion
    6. 0

      PPF installer for hire in SoCAL

      Hello. My name is Adrian i have good experience with paint protection film and i just moved to California, Irvine, i'm open to travel one hour away for the right job. You can contact me at 5717330693
      adrianpaun in Classifieds • Employment • Marketplace
    7. 11

      Boat window tinting tips

      or "bust out another thousand"
      TintDude in Window Tinting - General Discussion
    8. 11

      Boat window tinting tips

      Best tip would be, “Sorry, no boats”.
      pbalentine in Window Tinting - General Discussion
    9. 11

      Boat window tinting tips

      The answer is to not heat that area too much so that you leave some slack in the film for when you get it to the inside. Also cut your pattern a little large so that you can trim a thread off the edges after shrinking to not have a furled edge. After you do a few of those you'll figure out how much to leave/trim to not have any light gaps. Also I'll leave a hardcard wrapped in a microfiber in the bottom overnight to collect water and keep pressure on the film while it dries. Sometimes you can take the top rail off the glass if the jackwagon boat builder didn't put too much pressure on the glass package when it was installed. If you pull the rail off of a tight package it's a pita to get back on, looking like it could crack the whole time. Congrats on getting it done. I've seen plenty that couldn't, which is why I price them like I do.
      Dano in Window Tinting - General Discussion
    10. 11

      Boat window tinting tips

      Thx everyone for the tips the install went fine, however i did run into a new problem on the main curve of the glass from thr outside the tint would lay flat on the big curve but when applying it seemed like there was too much tension and it would not stay down i ended up heating it up and flattening down but some of that area got overheated and warped a little, if you know how to tackle this problem please help me thank you!
      Lauty in Window Tinting - General Discussion
×
×
  • Create New...