isolate doors 2005 altima

[watchdaride]

On a 2005 nissan altima do you need to isolate each door for a trigger input or can you run it to the dome light ? NOt sure if it has that dome light feature ( like GM )where it sends a ground to check if the doors arent left open .

[toodark]

12 VOLT CONSTANT GREEN (+) IGNITION SWITCH HARNESS

STARTER BLACK/RED (+) See NOTE *1 IGNITION SWITCH HARNESS

STARTER 2 BLACK/YELLOW (+) See NOTE *1 IGNITION SWITCH HARNESS

IGNITION 1 BLACK/RED (+) IGNITION SWITCH HARNESS

IGNITION 2 N/A

IGNITION 3 N/A

ACCESSORY/HEATER BLOWER 1 RED (+) IGNITION SWITCH HARNESS

ACCESSORY/HEATER BLOWER 2 WHITE/BLUE (+) IGNITION SWITCH HARNESS

KEYSENSE N/A

PARKING LIGHTS ( - ) N/A

PARKING LIGHTS ( + ) RED/BLUE (+) IN DRIVERS SIDE KICK PANEL, HARNESS TO REAR OF VEHICLE

POWER LOCK BROWN (Negative (-)) See NOTE *2 IN PIN 45, @ BCM RIGHT OF FUSEBOX

POWER UNLOCK PINK (Negative (-)) See NOTE *2 IN PIN 46, @ BCM RIGHT OF FUSEBOX

DOOR TRIGGER See NOTE *3 @ BCM, RIGHT OF THE FUSEBOX

DOMELIGHT SUPERVISION LIGHT BLUE (-) @ BCM, RIGHT OF THE FUSEBOX, PIN 47

TRUNK RELEASE RED/BLACK (-) or BLUE/RED (-) IN PIN 30, @ BCM, RIGHT OF FUSEBOX

SLIDING POWER DOOR N/A

HORN GREEN/WHITE (-) @ STEERING COLUMN HANRESS

TACH ANY WIRE NOT RED,PINK,or BLACK @ ANY IGNITION COIL

WAIT TO START LIGHT N/A

BRAKE RED/GREEN (+) @ SWITCH ABOVE BRAKE PEDAL

FACTORY ALARM DISARM WHITE/BLUE (-) See NOTE *4 IN PIN 5, @ MODULE IN DRIVERS DOOR

ANTI-THEFT TRANSPONDER ANTI-THEFT SYSTEM, REQUIRES 791 BYPASS MODULE AND EXTRA IGNITION KEY TRANSPONDER @ IGNITION SWITCH TUMBLER

EXTRA INFORMATION

NOTE *1 When Installing a REMOTE STARTER, you MUST use BOTH Starter #1 and Starter #2 wires. Both wires must be connected to the STARTER/CRANKING Output wire from the Remote Starter or the vehcile will NOT Remote Start when the Engine is cold. NOTE *2 TEST THESE WIRES WHILE TURNING KEY IN DRIVERS DOOR CYLINDER. NOTE *3 THE LEFT FRONT DOOR TRIGGER IS LIGHT BLUE(-) IN PIN 47. THE RIGHT FRONT DOOR TRIGGER IS PINK/BLUE(-) IN PIN 12. THE LEFT REAR DOOR TRIGGER IS RED/BLACK(-) IN PIN 48. THE RIGHT REAR DOOR TRIGGER IS RED/WHITE(-) IN PIN 13. WHEN CONNECTING TO AN ALARM SYSTEM, USE ALL 4 DOOR TRIGGER WIRES AND DIODE ISOLATE, TO CONNECT, SEE DIAGRAM NOTE *4 TEST THIS WIRE WHILE TURNING THE KEY IN THE DRIVERS DOOR KEY CYLINDER.

Isolate the doors.

[Guest CajunTinter]

Just like toodark says, you have to isolate all doors.......

Here's what I have: BCM to right of fuse box

The LF door is lt. blue in pin 47, RF door is pink/blue in pin 12, LR door is red/black in pin 48, and RR door is red/white in pin 13. Use all four wires and diode isolate each.

Good luck !!!

[watchdaride]

Just like toodark says, you have to isolate all doors.......

Here's what I have: BCM to right of fuse box

The LF door is lt. blue in pin 47, RF door is pink/blue in pin 12, LR door is red/black in pin 48, and RR door is red/white in pin 13. Use all four wires and diode isolate each.

Good luck !!!

thanks