Jump to content

90s thunderbird bg

Guest mrdave25

By Guest mrdave25
May 27, 2004 in Window Tinting - General Discussion

Recommended Posts

pierce8468

pierce8468

Posted June 30, 2004

- Report
- Share

Posted June 30, 2004

well I usually just lay it in and as it starts to roll, I heat it with the torch. let it marinate for a sec, push it down and maybe cool it off with the spayer.

but if you dont shrink it it wont roll back at all. just use the same basic install procedure you would for a newer camaro back glass that doesnt need shrinking

Link to comment

Share on other sites

Guest Eclipse

Guest Eclipse

Posted June 30, 2004

- Report
- Share

Posted June 30, 2004

Had 3 of these beauties this week already and just booked another one for next week. :rollin :thumb :lol :rollin

Link to comment

Share on other sites

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

Sponsored by
Activity Stream
1. 12
  Can this be fixed? Wondering how this happens
  
  Any impact from polishing, if the mar responds to polishing, would result in no or little visible trace. Anyone experienced in buffing glass will likely say, no guarantees; unless they've experienced the same mar on glass.
  
  1
  
  3 hours ago in Window Tinting - General Discussion
2. 7
  Boat window tinting tips
  
  I use(d) these that are readily available through grocery stores; on installs that should not have a blade running across their surface. https://www.walmart.com/ip/Scotch-Brite-3PK-Dobie-Cleaning-Pad/580762256?wmlspartner=wlpa&selectedSellerId=101033794&gclsrc=aw.ds&&adid=22222222227580762256_101033794_160178497084_20981201920&wl0=&wl1=g&wl2=c&wl3=689850595863&wl4=pla-2274697737319&wl5=9008682&wl6=&wl7=&wl8=&wl9=pla&wl10=255470249&wl11=online&wl12=580762256_101033794&veh=sem&gad_source=1&gclid=EAIaIQobChMIyo335LbOhQMVo0tHAR1HpQC8EAQYASABEgKydfD_BwE Need to know whether the boat has glass or does it have plexiglass (acrylic) or Lexan (poly-carbonate). Glass is not worrisome, the other two are. Plexi will blister from out-gassing in no time at all, whereby, Poly-carbonate is a crap shoot as to when and how serious, if any, blistering of film occurs. Both Plexi and Ploy may also be difficult to remove, if the need arises down the road mainly getting the adhesive of without damaging the surface. Both should not be warranted given the aforementioned potentials and these conditions should be discussed with the owner.
  
  1
  
  4 hours ago in Window Tinting - General Discussion
3. 12
  
  Can this be fixed? Wondering how this happens
  
  thank you - great to know polishing should remove it. 🙏 I appreciate you and all the others who took the time to reply.
  
  15 hours ago in Window Tinting - General Discussion
4. 12
  Can this be fixed? Wondering how this happens
  
  We've seen it on new vehicles, polishing it should remove it. Definitely not the shops fault.
  
  1
  
  17 hours ago in Window Tinting - General Discussion
5. 12
  
  Can this be fixed? Wondering how this happens
  
  no, aside from window cleaner I’ve not tried anything else yet like goo gone, a razerblade, etc… I’ll probably leave that to the detailer. question: when polishing glass will it impact the visibility after? I guess I’m now weighing between having them try to correct it or just leaving it be.
  
  19 hours ago in Window Tinting - General Discussion
6. 7
  
  Boat window tinting tips
  
  Amazon
  
  19 hours ago in Window Tinting - General Discussion
7. 1
  
  Geoshield vs Maxpro
  
  Global HP and Ceramic. Using it full time for seven years and not a single failure that wasn't my fault.
  
  19 hours ago in Window Tinting - General Discussion
8. 7
  
  Boat window tinting tips
  
  Where can i get a white scrubbie at locally like stapels, home depot, etc. dont have one in my toolbox yet
  
  19 hours ago in Window Tinting - General Discussion
9. 7
  
  Boat window tinting tips
  
  I start those at $750 and go up. Best advice is no cutting on the glass and white scrubbie only, no cleaning blades. That glass is super soft. You may want to use a film liner to make a template to cut your patterns.
  
  19 hours ago in Window Tinting - General Discussion
10. 1
  
  Geoshield vs Maxpro
  
  Hi! I’m new to the tinting world. Just completed a 5 day tinting course and want to purchase some films to start my mobile tinting. We trained with Geosheild, but there was a lot of talk about Maxpro and how it was good as well. Does anyone have experience with both of these? Which one is better to work with and easier to shrink? Prices on both are pretty close to each other. Any advice would be greatly appreciated. thank you!
  
  20 hours ago in Window Tinting - General Discussion

×

×

Create New...