Viktor

I also had the same problem little dot bubbles, i started to use distilled water and now its better.

pbotz2000 do you have any good news

last weekend i had one car, 4 perfect side windows, but the back window is like your white bubbles

1 hour ago, Super Dave said:

In the past, I’ve had a yellow turbo cut pretty long for cleaning back glasses. Recently, I cut down a Chanel squeegee to about 7 inches long and use that. The fewer passes cleaning the better, but you don’t want it so long that the squeegee can’t conform with the curve of the window. The last pass on the bottom edge I will use a 12 in black-n-white, cut at an angle. 

Thank you Super Dave.

Hi,

Thanks Tint Slayer,

Also can you recommend me best squeegee for clean the back window, now i have blue max

Hi ;)

i am looking for the best tool for cleaning the back window

16 minutes ago, Tint Slayer said:

Next time remove just the glass instead of the whole door ;-) 

This picture is only for example  ;)

here are tight side gaskets

5 hours ago, quality tintz said:

I have  a trick for tight side gaskets..are u bottom loading or top loading??

 top loading

Hi again

Today i had alfa romeo but with very very difficult seals on sides windows 

How i can to tint this car 

The rear window is ready but the sides not 

15 hours ago, quality tintz said:

Niceeeee!!!!! Cleannnn!!!

yes,no remarks

Side window suzuki swift, film global 5%

5 hours ago, quality tintz said:

Nice Viktor did u use baby shampoo or dawn??? Distilled water cheap $1.00 a gallon !

Yes with baby shampoo and distilled water 

The car was dirty inside maybe its better to clean before tint 

I am happy, i tried with distilled water it is the best way without dirt, thank you 

19 hours ago, Tint Slayer said:

Завийте един от тях върху кранчето, за да помогнете с водата. Или просто купете 1 литров бутилка вода, прибавете плъзгане право към него и завийте с пръскачка.
http://a.co/3J5yX4O 

12 hours ago, quality tintz said:

приятен

Yes nice,today i will try on my car ;)

21 hours ago, quality tintz said:

Make sure you use distilled water or filtered water for final install helps a lot !!!

Till now i use normal water maybe this is a problem thank you.

1 hour ago, Tint Slayer said:

@Viktor When spraying on slip right before install, use the slip to rinse the glass from the top down pushing dirt down, hit the sides spraying from the top down then do the whole glass spraying from the top downward (start about 1/2 inch/1cm from top). It should already be clean and this is where you'd be spraying on the slip anyway, so use it to rinse when applying, then apply film to the clean slip that remains.

Thank you for the instructions, i always have little dirt I'll try

3 hours ago, quality tintz said:

Blue shop towel and sprayway glass cleaner tested it today....then mist with baby shampoo and squeegee...rite before install....soak again install..

Good ;) i will test it

Hi,

16 hours ago, southcentraltinting said:

Are you peeling off the car or off a peel board? What does your prep consist of?  So many factors that include environmental conditions would determine the best course of action before the stick.

I am peeling off the car

For side windows first with scraper and glass cleaner after baby shampoo and squeegee and last alcohol

Seconds before i am instaling again baby shampoo and squeegee

Hi,

I am new in the business, i am tinting headlights and tail lights.

I have a question for the windows what is the best way to clean window seconds before instaling, for information i am using film Global and baby shampoo JJ.

Any advice will help me ;)