Jump to content

Solar Gard new UP darker films

trimguy

Recommended Posts

trimguy

trimguy

Posted
Posted

We did our first UP 40 job and were very impressed with the product. Shrunk nice for a very thick film. In fact we had to almost triple the down force on our plotter blade for this film. Any other observations?

Link to comment
Share on other sites
Fiveofeen

Fiveofeen

Posted
Posted
We did our first UP 40 job and were very impressed with the product. Shrunk nice for a very thick film. In fact we had to almost triple the down force on our plotter blade for this film. Any other observations?

My good friend who is all about plotters told me it was something like 260 was getting him the best results. On some cars it seems easier to pull panels and do extra shrinking on the outside before install to help it lay down nicely. If you need to give it a lot of heat to get it to lay down it wont react like a standard film, best to leave it be and hit it when its dried a little.

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

Go to topic listing
  •   Sponsored by
    auto-precut.com

    signwarehouse

    martinmetalwork.com

    rewiredtech.io

    tinttek

    filmvinyldesigns

    The Tint Tutor

    ride wrap

    Lexen

    Tint My Ride

    tintwiz

  • Activity Stream

    1. 0

      NOW HIRING: Experienced Automotive Tint/Vinyl Wrap Installer

      Tint World Louisville, KY Want to work in a state-of-the-art climate-controlled facility, for a company that will provide regular continuing training for a long-term career, and commissions you can support a family on? Must be willing to learn PPF and / or Vehicle Wraps if no experience. We are willing to train the right candidate. You bring the right attitude and work ethic, and we will train you for a very lucrative career. We’re offering a very competitive base salary against commission, with unlimited income potential including bonuses, spiffs, and incentives! Come join the fastest growing and highest paying auto styling company in the business. Why Join Us? Comfortable Environment: Climate-controlled installation facility. Precision Work: Use of a plotter for precision pattern cuts. Pioneer: The area's first one-stop shop for all automotive aftermarket needs. Franchise Support: All the resources necessary for your success. Growth: One location with more stores planned. Veteran-Owned: Focus on family and team. What We Offer: Competitive Salary against commissions. Full-Time: 5-day work week, 8 am - 6 pm, promoting a healthy work-life balance. Paid Time Off: Birthday, holidays, and vacation. Career Growth: Promotion from within and management training. Employee discount Year round work On-the-job training To submit a resume for consideration call or text Alex at (615)779-3132 or email alex.hellervik@tintworld.com Job Type: Full-time Pay: $40,000.00 - $100,000.00 per year Experience: Automotive Window Tint or Vinyl Wrap: 2 years (Required) Ability to Commute: Louisville, KY 40218 (Required)
      AmericanClassic275 in Classifieds • Employment • Marketplace
    2. 1

      The direction of shrink

      On some smaller pieces, sometimes. Mostly, no. The fingers will be too narrow to shrink down. If you do get it to lay flat the amount of stress you put on the film will shorten its lifespan.
      Dano in Window Tinting - General Discussion
    3. 1

      The direction of shrink

      Hi all, First, I know little about tinting at all and am trying to learn how to do it as sort of a fun project, as I enjoy learning things like this. I was told that the film shrinks up or down, not sideways. If that is the case, would it make more sense to rotate the film and shrink perpendicular to the fingers, instead of parallel to the fingers?
      Hobbyist in Window Tinting - General Discussion
    4. 1

      Graphtec Plotter

      I've had that happen. I've solved it a few different ways. Sometimes uninstalling/reinstalling the cut program. Sometimes by doing the same with the cutters driver. Other times just by restarting the computer and/or unplugging and restarting the cutter. Seems like it can happen without any obvious reason. I've had it decide to change tools and start pouncing the pattern after cutting the first half just fine. I've also had the driver forget how to output and had to reinstall a USB port that it was recognising for years. Those machines can be quirky and sometimes have to be set back up from scratch and will run fine again for years only to later flake out...and start running fine again. I would like to blame the motherboard or the driver most of the time for corrupting the file, which is why I usually start with the driver. Also it's good to let the motherboard warm up if you're running an older machine. If I run mine cold it will sometimes drop the file out of buffer. Now I just leave it on 24/7 to keep the board warm. If you do get a solid answer from Graphtech, please let us know what you found.
      Dano in Plotters and Cutting Systems
    5. 2

      Llumar air 80 vs 3m Crystalline - dealer advised to go regular 3m ceramic over Crystalline

      @Tintguy1980 pretty much covered the difference in the films. Since Ceramic films absorb the heat, the vehicle must be in motion to push the hot air away. No motion means more heat building up in the glass and radiating inward to you. Since Crystalline redirects heat away, the radiating inward heat is much less if you are in traffic or sitting still. As far as the shop, they either don't want to stock Crystalline since it is $$$$ per roll or do not want to install it since it takes more work and time. Also, not all 3M dealers can install Crystalline. If you check the dealer locator, if they do not have "Crystalline Preferred" listed, then this is most likely the case. With that being said, we absolutely love the Ceramic IR line, so you can't go wrong there.
      DynamicATL in Window Tinting - General Discussion
    6. 1

      Graphtec Plotter

      I should reach out to graphtec about this issue, but I'm curious if anyone else has experienced the same problem with their plotter. My graphtec plotter can cut specific designs flawlessly without any problems with pressure or shape. Occasionally I experience an issue where I will plot a design consisting of two fronts or a rear windshield window, and the cut is flawless, but just before the plotter finishes, allowing me to remove the excess material from the machine. It reaches the end as if it will finish feeding it completely and then abruptly lowers the blade as if it still needs to cut the design, slicing right through the pattern it just created. Do you have any thoughts on why that occurs?
      Tintguy Santa in Plotters and Cutting Systems
    7. 0

      FOR SALE Jaguar V LX 40" plotter

      Selling a like new Jaguar VLX 40" plotter. Works perfectly, we upgraded to another plotter and don't have space for this one. Only available for pickup, located in Orange County. If interested or you have any questions please contact us at 949-888-6581. Priced at $3,800 OBO.
      AudioToyz in Plotters and Cutting Systems
    8. 2

      Llumar air 80 vs 3m Crystalline - dealer advised to go regular 3m ceramic over Crystalline

      Easy technical explanation of the difference between Crystalline and regular 'ceramic' labeled products, including 3Ms: Crystalline is designed to 'reflect' NIR (Near Infrared, the sun's energy we 'feel' first) as opposed to 'ceramic' products absorbing. Absorbing translates into feeling the sun's energy radiating off the window as your arm is rested next to it. Therefore, Crystalline is superior to ceramics. This is the pitch I would make to you as a buyer. Maybe the dealer you spoke with simply doesn't want to pay the price for a roll of the product. I've had Crystalline 40 on my front door glass for 8 yrs now and it shows zero sign of any degradation in color, performance and clarity. Crystalline would be better than AIR80 for the windshield as well.
      Tintguy1980 in Window Tinting - General Discussion
    9. 2

      Llumar air 80 vs 3m Crystalline - dealer advised to go regular 3m ceramic over Crystalline

      I just got off the phone with a 3m dealer in Dallas and he strongly advised me to save my money and get their regular ceramic and not the 3M Crystalline. He said I'd never know the difference and acted like it was NOTHING more than a marketing strategy. So that's got me all confused. He could make more money off me, but I feel like he's being honest and I appreciate that. But, then I hear everywhere else how much better Crystalline is over other products. So, I'm still debating on Air 80 or Crystalline for the windshield and Llumar IRx or Formula 1 or 3m Crystalline for the other windows.. So much to consider! FYI, I generally like the best for a couple hundred more, BUT I do want there to be some improvement.
      dtximages in Window Tinting - General Discussion
    10. 1

      Reimbursement for warranty work on solar or safety film

      Crap shoot.
      Tintguy1980 in Window Tinting - General Discussion
×
×
  • Create New...