Jump to content

Decorative help please

tntautoglass

Recommended Posts

tntautoglass

tntautoglass

Posted
Posted

I'm not real familiar with decorative installs. I have a customer asking about 3M Milky crystal and 3M Essen. I do have a sample book from 3M. Is the 3M Milky similar to a Llumar/Suntek white matte? Also, I was told one window size is 84"x84" and on 72"x84". Do you have worry about glass breakage with these films? Please don't harass me about my inexperience with deco. Just looking for info. Thanks.

And is there anything else out there comparable to 3M Essen?

Link to comment
Share on other sites
TomTint

TomTint

Posted
Posted

They both have a raised texture to them. The Matt crystal is similar to most basic frost films but not exact. The Essen may be hard to equal. It is a bit clearer than frost and has speckles in it. Call deco films to see if there is a equal and if not get the 3M. I would not be concerned with glass breakage, but seeming may not look very good

Link to comment
Share on other sites
tntautoglass

tntautoglass

Posted
  • Author
Posted

They both have a raised texture to them. The Matt crystal is similar to most basic frost films but not exact. The Essen may be hard to equal. It is a bit clearer than frost and has speckles in it. Call deco films to see if there is a equal and if not get the 3M. I would not be concerned with glass breakage, but seeming may not look very good

Thanks Tom. You said "matt crystal" is that the same as Milky crystal?
Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

Go to topic listing
  •   Sponsored by
    ride wrap

    Lexen

    tintwiz

    auto-precut.com

    signwarehouse

    martinmetalwork.com

    tinttek

    filmvinyldesigns

  • Activity Stream

    1. 0

      Stratos 70 on windshield, what is this?

      I can't win with getting tint decent on the windshield. I had 3M on my F150 done twice and still has major defects. Recently did Stratos twice on my F350 and I see this granular spotted, texture pattern on the tint. It's super obvious in the corner here but also right in my view when driving. It's honestly hard to point out and show someone but when your driving and stuff is moving behind the windshield, it becomes more obvious. The lighting also matters. The first time I did the windshield, I had a two foot line on the windshield. Thinking it was tint, they removed the tint and it was apparently a defect in the Ford windshield. An issue between the laminated glass layers caused this big defect. So they removed the tint, I had Ford replace the windshield on a 2024 F350 but when the tint shop removed the tint, they made a bunch of micro scratches in the front windshield, probably from scrapping the glue off. I told them but I didn't care since Ford was replacing the windshield anyways. So if basically I'm trying to figure out what this texture stuff is and if I should have them replace or remove it. Replacing it might just have different issues but also afraid they will scratch the windshield.
      dseg42 in Window Tinting - General Discussion
    2. 1

      Wtb Solar Gard Supreme NR 40

      I would direct you to Express Window Films web site. They sell Global brand after setting up an account with them. They are reasonably priced and they do partials. Can't go wrong with Global.
      Tintguy1980 in Window Tinting - General Discussion
    3. 6

      Need some help

      Never overlook the condition of the floor. Back when I did install, I used to mist the floor between the vehicle and the peel board. This is done between misting the window and walking toward the peel board to mist the pattern liner, peel liner and spray adhesive for install. Tacks any dust for the duration of each pattern install, so repeat each time a pattern is going to be installed.
      Tintguy1980 in Window Tinting - General Discussion
    4. 2

      Olfa blades are not as sharp as they used to be

      Yeah, at least a decade ago rumored to be different as a result of a US based manufacturer making Olfa blades sold here at home. Of course, Olfa would deny coupling up with a US maker. I, too, switched to NT.
      Tintguy1980 in Window Tinting - General Discussion
    5. 2

      Olfa blades are not as sharp as they used to be

      Olfa has been terrible for years. Switched to NT a long time ago.
      Dano in Window Tinting - General Discussion
    6. 2

      Olfa blades are not as sharp as they used to be

      We have been using olfa blades forever but in the past year we have noticed the quality of the blades is not the same as it used to be. Blades are not as sharp and pressing harder is starting to etch the glass on certain vehicles. Would like to know if anyone else is experiencing this or is there a better brand ss blades that you have been using that is a better trusted brand.
      qttire1 in Window Tinting - General Discussion
    7. 3

      Help Needed! - Graphtec FC4100-75 - Software/Compatibility/Drivers/Communication/Blades/Setup

      Bump on this. I spoke with Film & Vinyl Design and the rep told me their cutting software contains the drivers for the Graphtec 4100 models. They also mentioned it will work with Windows 11. Any one have experience with this program, good or bad things to say about it?
      LuxAuto in Graphtec
    8. 6

      Need some help

      Push out all the air you can then… Heat up area with heat gun and use a hard card to press them down while everything is still fresh… don’t over heat prep work is key… you can also use masking tape on the gaskets and carefully peel the tape out once you have all the fingers out
      Klaveraid in Window Tinting - General Discussion
    9. 1

      Wtb Solar Gard Supreme NR 40

      Would like to buy a partial roll of the Solar Gard Supreme NR 40… needs to about 25ft x 30” plus and a 5% strip for the front windshield let me know if you could help out just a former window tinted here the has a new truck I wanna work on Thanks
      Klaveraid in Window Tinting - General Discussion
    10. 0

      Canadian Tinter Looking for work in US

      35 years old. Over 10 years in the field doing automotive tint and ppf. Currently managing / working as main installer in Edmonton, Alberta. Xpel/Suntek, DAP/Core experience. Long story short, Canada became boring and i would want to give US a shot. Love what i am doing, getting paid well for where i am but i know i can do more & its hard to jump higher than your head where i am. if there are shops that are willing to provide i good Canadian installer a job offer i would like to talk. P.S. Would love to be in the place that is busy year round.
      sasktinter in Classifieds • Employment • Marketplace
×
×
  • Create New...