quality tintz

Hope this helps!

Don't throw your bulldozer away when the blade falls off just mask it with some masking tape and super glue it when its falling apart I've had the same one for years my friend has bought about 3 or 4..also i never use mine with heat gun just yellow bigfoot with heat......

Have you ever finished a side window and there's a gap on the back or front when it rolls up well here is the trick lift the film and dry it make a circle on the window with a sharpie make sure it's a fat Sharpie and press the tint on it you will have a mark now when you're on the inside just line up the mark that's where it goes when you're done clean both sides with a little alcohol lines up perfect

3 hours ago, poppawilly67 said:

ive been bouncing back and forth with a tape measure.  good tip!!!

Thats what we here for bro !!!

Good tips

11 hours ago, Whyme said:

I’ve been using solargard nr supreme for over ten years . Tinting with it everyday ! I like it , shapes well . Installs well . The color matches the stock color that comes on the back of most vehicles from the factory . My customers like it . I have not had any complaints . It’s not a ceramic film, or nano film, but I like it . 

Where u been any more videos outside

When you are doing a visor strip it sometimes sucks going back and forth with a tape measure my friend taught me to measure from the top and make several marks like 8 in 9 inch 10 inch and 11 inch say like four marks then you can just line the tint with a factory Edge on the two Sharpie lines and cut off the top when you install you just line up the tint to the line you picked it helps a lot on not going back and forth with a tape measure this is for hand cutting....

Great tips thanks alot !!!

3 hours ago, Tint Slayer said:

What's your opinion on it? Cleaner/better than frankenstein? 

Yes and more detail soak the pattern or window or both??? Lots of slip in solution please explain ????

What is the key to this having everything super clean around reverse roll ???

11 hours ago, jsylva said:

Did my first Model 3 last week, we did the the whole thing including windshield in ceramic and also did the entire front end in PPF. Customer is loving it and i actually enjoyed working on this car. My helper did crunch a cut out while i was shrinking he opened a door on the other side and those shoot down quite a bit so had to re cut that door but it was hella funny seeing his reaction. Love this forum thanks for everyone's input . 

How do you do your windshields reverse roll ???

Ammonia or straight alchohol works good protect door panels with something though 

Thanks guys!!!!

Nice whole panel had to come off cause it overlaps on door panel.and that little speaker is in the way.. one side I took the door panel off and the other side I just top loaded with the panel on it wasn't bad it's out the door

4 hours ago, pottsnpanz said:

All new Acura's are very easy. 2 screws behind the door handle and 2 screws behind the handle on the panel door panel and pop all the tabs. Some of them you just need to pop the top of the panel off of the seal.

Is this one where just top panel pops???

3 hours ago, Tint Slayer said:

Wooden popsicle stick is a great tool for pushing out that little stuff and crushing specs. Also if you have a pink Lil Chizler you can heat up and bend a corner and use the rounded end for rubbing that out and crushing specs. Just mentioning.

Why heat the chizler???

11 hours ago, Stewy said:

Yes. Very easy. We do the acura delearship now. And all Acura are easy. Just search the amp for everyone of these high end vehicles and you will be fine. I have DEI app and that helps with searching all the vehicle amplifiers.

Where is amp on this one ??? Acura rdx???

Get that doe bro !!!! Ask him what he does for a living 20 million dammmmm!!!!!

Cut on defroster line like they said push up to cut and top down to cut.....bubble gone if glue on film is good...try some heat or in direct sun if bubbles are stubborn.....

Has anyone done 2018 acura rdx ???are they easy ???

I teach you in new mexico or go to where you are for the rite price!!??

Smooth it all out small stuff will squeegee out but try to lay it all down 

That is a finger bro!!!!!

Can u scan your own patterns or send the liner back to the company

57 minutes ago, Jake said:

WOW! That's the cheapest Crystaline install I have ever heard of. Whats your location?

 

Hope its not reboxed ebay tint hahhah!!!