Jump to content

Soundproof film???

Safehaven
 Share

Recommended Posts

Guest 24/7 Barking dogs tint

Guest 24/7 Barking dogs tint

Posted
Posted

Residential home with many barking dogs 24/7.  Owners do not take care of their animals. I can’t find the house to ask them to take care of their barking dogs.  The poor dog is out of the house in the rain, 115 degree weather and it’s very sad. I need soundproof and to tint my bedroom windows due to extreme heat during the day.  Need quote. I even have black out drapes and they stopped working.  My number is :: 951-330-9906. My name is Kim.  I really hope this tinting works?  It gets so hot in my bedroom and then the barking dog noises.   Thank you for the quote.  I have 2 standard windows.  I hope that makes sense?

Link to comment
Share on other sites
Bham

Bham

Posted
Posted
18 hours ago, Guest 24/7 Barking dogs tint said:

Residential home with many barking dogs 24/7.  Owners do not take care of their animals. I can’t find the house to ask them to take care of their barking dogs.  The poor dog is out of the house in the rain, 115 degree weather and it’s very sad. I need soundproof and to tint my bedroom windows due to extreme heat during the day.  Need quote. I even have black out drapes and they stopped working.  My number is :: 951-330-9906. My name is Kim.  I really hope this tinting works?  It gets so hot in my bedroom and then the barking dog noises.   Thank you for the quote.  I have 2 standard windows.  I hope that makes sense?

 

Window Tint will fix the heat problems, but not the sound.  Sound had to be blocked or absorbed by "mass". Soundproof glass works because of the thickness of it. Same with soundproof foam.  It absorbs sound when it travels through the foam.    

Window tint does not have the mass necessary to be functional as a sound deadening device.  

Link to comment
Share on other sites
TomTint

TomTint

Posted
Posted
On 1/4/2020 at 11:23 AM, Bham said:

 

Window Tint will fix the heat problems, but not the sound.  Sound had to be blocked or absorbed by "mass". Soundproof glass works because of the thickness of it. Same with soundproof foam.  It absorbs sound when it travels through the foam.    

Window tint does not have the mass necessary to be functional as a sound deadening device.  

  

   Most of the sound deadning material out there has multiple angles and depth contours that absorb different wavelengths of sound. 

 Lately the OEM auto mfrs have been using laminated glass instead of tempered to make the cabin of their cars more quiet. For a retrofit  soundproofing measure..PPF can be used and it's actually pretty effective. 

Link to comment
Share on other sites
Bham

Bham

Posted
Posted (edited)
13 minutes ago, TomTint said:

  

   Most of the sound deadning material out there has multiple angles and depth contours that absorb different wavelengths of sound. 

 Lately the OEM auto mfrs have been using laminated glass instead of tempered to make the cabin of their cars more quiet. For a retrofit  soundproofing measure..PPF can be used and it's actually pretty effective. 

 

Yes sir, the laminate essentially keeps the glass from resonating or vibrating.  Also being a plastic material the extra layer will scatter sound waves (a bit).  

BUT, Not very effective for direct sound waves such as radios or sirens but slightly more effective than plain glass.  It keeps down road noise but a lot of that noise is due to vibration and wind travel not direct sound waves.  

 

I just don't see it being very effective for dogs barking without A LOT of it being used.  Hence,, more mass.  :twocents    

Edited by Bham
Link to comment
Share on other sites
TomTint

TomTint

Posted
Posted
6 minutes ago, Bham said:

 

Yes sir, the laminate essentially keeps the glass from resonating or vibrating.  Also being a plastic material the extra layer will scatter sound waves (a bit).  

BUT, Not very effective for direct sound waves such as radios or sirens but slightly more effective than plain glass.  It keeps down road noise but a lot of that noise is due to vibration and wind travel not direct sound waves.  

 

I just don't see it being very effective for dogs barking without A LOT of it being used.  Hence,, more mass.  :twocents    

 

  Different sounds resonate at different frequencies. I have no idea what the science is behind any of them. I would suspect that what is being used in OE auto is engineered to mitigate wind and other low frequency noises. But probably not sirens or horns that are high frequency and DB. 

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing
  •   Sponsored by
    signwarehouse

    martinmetalwork.com

    rewiredtech.io

    tinttek

    filmvinyldesigns

    The Tint Tutor

    ride wrap

    Lexen

    Tint My Ride

    tintwiz

    auto-precut.com

  • Activity Stream

    1. 1

      Graphtec Plotter

      I've had that happen. I've solved it a few different ways. Sometimes uninstalling/reinstalling the cut program. Sometimes by doing the same with the cutters driver. Other times just by restarting the computer and/or unplugging and restarting the cutter. Seems like it can happen without any obvious reason. I've had it decide to change tools and start pouncing the pattern after cutting the first half just fine. I've also had the driver forget how to output and had to reinstall a USB port that it was recognising for years. Those machines can be quirky and sometimes have to be set back up from scratch and will run fine again for years only to later flake out...and start running fine again. I would like to blame the motherboard or the driver most of the time for corrupting the file, which is why I usually start with the driver. Also it's good to let the motherboard warm up if you're running an older machine. If I run mine cold it will sometimes drop the file out of buffer. Now I just leave it on 24/7 to keep the board warm. If you do get a solid answer from Graphtech, please let us know what you found.
      Dano in Plotters and Cutting Systems
    2. 2

      Llumar air 80 vs 3m Crystalline - dealer advised to go regular 3m ceramic over Crystalline

      @Tintguy1980 pretty much covered the difference in the films. Since Ceramic films absorb the heat, the vehicle must be in motion to push the hot air away. No motion means more heat building up in the glass and radiating inward to you. Since Crystalline redirects heat away, the radiating inward heat is much less if you are in traffic or sitting still. As far as the shop, they either don't want to stock Crystalline since it is $$$$ per roll or do not want to install it since it takes more work and time. Also, not all 3M dealers can install Crystalline. If you check the dealer locator, if they do not have "Crystalline Preferred" listed, then this is most likely the case. With that being said, we absolutely love the Ceramic IR line, so you can't go wrong there.
      DynamicATL in Window Tinting - General Discussion
    3. 1

      Graphtec Plotter

      I should reach out to graphtec about this issue, but I'm curious if anyone else has experienced the same problem with their plotter. My graphtec plotter can cut specific designs flawlessly without any problems with pressure or shape. Occasionally I experience an issue where I will plot a design consisting of two fronts or a rear windshield window, and the cut is flawless, but just before the plotter finishes, allowing me to remove the excess material from the machine. It reaches the end as if it will finish feeding it completely and then abruptly lowers the blade as if it still needs to cut the design, slicing right through the pattern it just created. Do you have any thoughts on why that occurs?
      Tintguy Santa in Plotters and Cutting Systems
    4. 0

      FOR SALE Jaguar V LX 40" plotter

      Selling a like new Jaguar VLX 40" plotter. Works perfectly, we upgraded to another plotter and don't have space for this one. Only available for pickup, located in Orange County. If interested or you have any questions please contact us at 949-888-6581. Priced at $3,800 OBO.
      AudioToyz in Plotters and Cutting Systems
    5. 2

      Llumar air 80 vs 3m Crystalline - dealer advised to go regular 3m ceramic over Crystalline

      Easy technical explanation of the difference between Crystalline and regular 'ceramic' labeled products, including 3Ms: Crystalline is designed to 'reflect' NIR (Near Infrared, the sun's energy we 'feel' first) as opposed to 'ceramic' products absorbing. Absorbing translates into feeling the sun's energy radiating off the window as your arm is rested next to it. Therefore, Crystalline is superior to ceramics. This is the pitch I would make to you as a buyer. Maybe the dealer you spoke with simply doesn't want to pay the price for a roll of the product. I've had Crystalline 40 on my front door glass for 8 yrs now and it shows zero sign of any degradation in color, performance and clarity. Crystalline would be better than AIR80 for the windshield as well.
      Tintguy1980 in Window Tinting - General Discussion
    6. 2

      Llumar air 80 vs 3m Crystalline - dealer advised to go regular 3m ceramic over Crystalline

      I just got off the phone with a 3m dealer in Dallas and he strongly advised me to save my money and get their regular ceramic and not the 3M Crystalline. He said I'd never know the difference and acted like it was NOTHING more than a marketing strategy. So that's got me all confused. He could make more money off me, but I feel like he's being honest and I appreciate that. But, then I hear everywhere else how much better Crystalline is over other products. So, I'm still debating on Air 80 or Crystalline for the windshield and Llumar IRx or Formula 1 or 3m Crystalline for the other windows.. So much to consider! FYI, I generally like the best for a couple hundred more, BUT I do want there to be some improvement.
      dtximages in Window Tinting - General Discussion
    7. 1

      Reimbursement for warranty work on solar or safety film

      Crap shoot.
      Tintguy1980 in Window Tinting - General Discussion
    8. 1

      Beginner trying to learn, where I'm at...

      Welcome to the forum! I would recommend Global non-cap ppf and get a second bottle with plain water only to flush the edges for better adhesion. If you're leaving water behind try using a different squeegee. I prefer a dark yellow turbo from Interwest. Instead of heating I think you should be streaching the film into place to pull the fingers out.
      Dano in Paint Protection Film, Clear Bra Forum
    9. 4,178

      What did you tint today?

      Y'all try not to get too excited, but this is the four cylinder Suzuki version of the Geo Metro with a whopping 1.3L. No ac or power steering but getting 45mpg on 13" rims.
      Dano in Window Tinting - General Discussion
    10. 1

      Beginner trying to learn, where I'm at...

      Hello, thanks for allowing me to join. I'm a retired auto technician/High School Automotive Instructor. Enjoyed working on cars all of my life. I have had and still have several nice cars (mostly Corvettes) and enjoy keepng them nice. I have a lift in my garage which helps with the install on lower areas of the vehicle. I have been tinkering with PPF film here and there on rock chip prone areas on my cars. I have been sucessful sometimes installing where it was acceptable to my liking, but never perfect. I have had to rip several off and start over. That doesn't bother me because I really want to master this. Education isn't free and if it means wasting film and time I understand. I have gotten over the fear of installing it on small areas (front of wheel well area on rear quarter of C8 Corvette) and shrinking it with heat gun to smooth out fingers but cannot do an insatll without getting any bubbles completely. Some installs the bubbles have dried over a couple of weeks and were acceptable for me. But other installs were not, and I had to start over. The solution I'm using is the typical 16oz distilled water and 2 or 3 drops of baby shampoo. The film is Ebay pre-cut kits. Can anyone shed any light as to what I'm doing wrong to minimize the bubbles? Is there a different solution I should be using? Is there a better film to start with that is easier to use for beginners? I'd appreciate any advice or tips I can get. Thanks in advance!
      vetteowner in Paint Protection Film, Clear Bra Forum
×
×
  • Create New...