Jump to content

2018 Camry

Booms

Recommended Posts

Booms

Booms

Posted
Posted

So, finally got a chance to do one today.

Doors are a breeze...... absolutely no shrinking necessary, and the gasket is a least 1/4 inch below the top of the door panel. No tucking! :clap

Back window is a least half the size of the last model year, and a very easy shrink. Don't be skurred of the curve at the top... :lol   It's a lot easier than it looks.

 

Now on to hanging the back window..... :gasp

 

The top of the window starts in back of the headrests! Headrests that you can't take out ! The bottom of the window is at least two feet in.

It's easier to hang because it's half the size, but it's harder to get to. So, a draw on the back window.

All in all, a very easy car to tint. Even with the raggedy back window. :cool

 

2018Camry.jpg

Link to comment
Share on other sites
Apex Tint

Apex Tint

Posted
Posted
1 hour ago, Booms said:

So, finally got a chance to do one today.

Doors are a breeze...... absolutely no shrinking necessary, and the gasket is a least 1/4 inch below the top of the door panel. No tucking! :clap

 

Have you ever had any issues with peeling from not tucking film below the gasket?

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

Go to topic listing
  •   Sponsored by
    Conco

    Lexen

    tintwiz

    auto-precut.com

    signwarehouse

    martinmetalwork.com

    tinttek

    filmvinyldesigns

    ride wrap

  • Activity Stream

    1. 2

      Cracked glass

      Hey, thank you for taking the time to reply. It's greatly appreciated!
      Geyser in Window Tinting - General Discussion
    2. 3

      Automotive Tint Comparison

      1) Why avoid Suntek? I thought they resolved that issued with the easy scratching and that they are one of the market leaders in Australia? Also, it seems most of the well established Tint businesses use Suntek 2) I've heard mixed things about Rayno, with some installers raving about it and others disparaging it. Makes it difficult for the consumer to know the truth, given vested interests exist. 3) Is Ultragard a Australian exclusive product? The IP seems to be owned by GTS FILMS PTY LTD. How's the quality as it seems to have limited installers. 4) Is the MEP Films CNP that apparently are Manufactured by LLumar of the same quality as the LLumar tints (such as Llumar Formula One Stratos; Llumar Formula One Pinnacle; Llumar CTX)? 5)
      MVOZ in Window Tinting - General Discussion
    3. 2

      Cracked glass

      The crack indicates thermal stress, however, the edge of the glass may have an imperfection (bur or clam shell chip). The crack does run 90 degrees out from the edge and curves as it follows any weaknesses in the pane itself. I have attached a pictured of what tempered glass looks like when it breaks and alongside it what a plate (or float) and heat-strengthened glass looks like when it breaks. The outer panel my be tempered should indicate so by a stamp etched on the glass surface in one corner. It should indicate tempered. Plate glass has no indicators, however, heat-strengthened glass will crack in the same manner as plate glass. I'm an unsure whether heat-strengthened glass requires a stamp. Tempered glass is 4 times stronger than plate and heat-strengthened is 2 times stronger than plate. 1 in 24 is indicative of edge imperfection. I could not find the solar absorption rate of DN 50, but if it is similar to competitive films, there should be no issue with that installation setting (including a straight line shadow). This, too, points back to edge imperfection as the cause. And finally, I spy drapes in a close position, correct? If so, it would be helpful to crack open during sun exposure; this to assist in allowing trapped heat between the glass and drapes to dissipate.
      Tintguy1980 in Window Tinting - General Discussion
    4. 2

      Cracked glass

      Hello. I recently installed Johnson Daylight Natural DN 50 on a couple of windows. Solar energy rejection is 39%. The windows are double pane and the glass is supposed to be tempered 4mm + tempered 6mm. The roof overhang shades the top 1/3 - 1/2 of the windows. However, a few days after installation I noticed that one of the glass has cracked, presumably due to thermal stress. Should I remove the film from the rest of the windows? I installed the film on 24 of these windows (6 tiny houses) so now 1 out of 24 is broken. Or is it more likely that I just got unlucky and the glass had a defect? Is shading from the roof overhang such a big factor? The glass cracked. Is it really tempered? I thought tempered glass would shatter, but not crack. Thanks!
      Geyser in Window Tinting - General Discussion
    5. 6

      Residential Window Tint - Suntek SYDS vs. Solar Gard Slate vs. Madico Optivision

      Did you get this taken care of? What were the results and are you pleased?
      LeadfootCJ7 in Window Tinting - General Discussion
    6. 1

      Residential Film without blue hue?

      Take a look at 3M's Nightvision or LLumar's Dual Reflective series, they both have a warm tone to them.
      Tintguy1980 in Window Tinting - General Discussion
    7. 3

      Automotive Tint Comparison

      Steer clear of Black Armour, Suntek, ASWF. The others are good choices if you are in Australia. Check out the reviews of the installer too. It’s not just the materials that have to be proper. Never go for the cheapest!!!
      jj in Window Tinting - General Discussion
    8. 1

      Residential Film without blue hue?

      Hey guys I am in the process of having window film installed in my home but have a question about which brand I should go with. Hoping yall can help me out. I have a room that faces a busy street and as a result my blinds pretty much always stay closed. I love having natural daylight but not so much people being able to see what i'm doing in my room/all my expensive equipment. I used to work in the window film industry as a helper/installer/salesman when I was in highschool and we did a lot residential/commercial work. The specific brand of film we used always left a certain blue and cool appearance. Is there any brand of residential film that does not have this effect? I mainly just cannot stand having blue light amplified and am looking for a film that has a neutral shade to it or even a warm/yellow hue. I have single pane windows and I do not necessarily care about heat rejection but if I have to pay more for a ceramic film rather than a dual reflective or a standard film I am willing to if that helps solve the issue. Again, any help is really appreciated with this there are so many new window film brands out there and it really is cool to see how far the industry has come.
      dennis_fl in Window Tinting - General Discussion
    9. 8

      South facing window tint

      Thanks for the vote of confidence Tintguy. Recoil, we will take good care of you.
      jnf in Window Tinting - General Discussion
    10. 8

      South facing window tint

      Thank you gents, I will reach out. Appreciate you both!
      Recoil in Window Tinting - General Discussion
×
×
  • Create New...