Jump to content

Wax technique

TintJunkie

Recommended Posts

TintJunkie

TintJunkie

Posted
Posted

Instead of using baby powder, use wax. I use some "shaping spray" from my distributor. Enprodistributing.com.

Spray it on, or if not in a can, wipe a small amount on the back glass. Let haze up a little. Do your "H" with a damp paper towel to anchor the film and shape from the middle up/down. You can hold a heat gun on the film for a long time with wax before it starts to burn the film.

Anyone else do em this way? At least for more curved back glass's??

Link to comment
Share on other sites
Guest Texstar

Guest Texstar

Posted
Posted
A new one to me but sounds well worth a try. thanks guys :dunno

Its basically the same as the slip solution spray on and soap method. The wax just drys to a light haze and give the film the float. Good luck :spit

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

Go to topic listing
  •   Sponsored by
    martinmetalwork.com

    tinttek

    filmvinyldesigns

    ride wrap

    Conco

    Lexen

    tintwiz

    auto-precut.com

    signwarehouse

  • Activity Stream

    1. 0

      South facing window tint

      Hi folks, I have south facing double pane windows that get a lot sun here in Las Vegas. Those windows get extremely hot and I want to get them tinted. I do not mind if they are black, mirror, dark, light, etc. I am looking for performance blocking the heat without doing a complete blackout. Initially I was thinking of going with 3M Prestige 70 since 3M is the only reputable brand I could think but I did read a few posts here in the forum and I see that there is other brands with perhaps better products like “Huper Optik”. I have not reached out to installers yet since I wanted to research what would be the best product for my needs, could you folks recommend a product that would fit the bill? Thank you!
      Recoil in Window Tinting - General Discussion
    2. 4

      Wet shrinking problems with certain windows

      Dry shrink is akin to moving from the horse and buggy age to the age of automobiles; not only innovative, but you find yourself getting to your destination quicker. Dry shrink is also less damaging to the chemical properties of the film itself. And like Bham has pointed out in different words, work smart not harder. TD mentioned the wet check after dry shrinking, which is a technique used by many in the early stages of learning to dry shrink. Plenty of demos on Youtube.
      Tintguy1980 in Window Tinting - General Discussion
    3. 4

      Wet shrinking problems with certain windows

      You REALLY need to learn to dry shrink. That type of finger would not happen and would be way easier to manipulate before failure. It's not about the time you wait for the prep surface to dry, it is about the ease of shrinking difficult windows without them being difficult. Dry shrinking makes our work so much easier. Your quality of installs will go way up and time spent on tough back glasses or windshields will go way down. The stress of doing a difficult shrink is way less once you learn the ropes of dry shrinking. If you want to improve your craft and get better at installs you are probably gonna have to learn to dry shrink sooner or later.
      Bham in Window Tinting - General Discussion
    4. 4

      Wet shrinking problems with certain windows

      So theres no way to get around it by wet shrinking it? I havent touched dry shrinking once and dont really have the time to way for the dryer sheets to dry could i just use water as a grip methood?
      Lauty in Window Tinting - General Discussion
    5. 4

      Wet shrinking problems with certain windows

      Wet shrinking has advantages but it also has limitations. I'd learn a good dry shrink technique, then follow up with a wet check. You can get a lot more shrink into a piece doing it dry with a lot less stress on the film.
      TintDude in Window Tinting - General Discussion
    6. 4

      Wet shrinking problems with certain windows

      hey everyone today i was tinting a BMW front windshield i don't remember which model. Anyways while shrinking fingers closer to the side edge it seems like it will end up creasing while i follow the wet shrinking process. I would like to learn how to fix this or get around it i also would like to stick to wet shrinking heres a video to see what happened and fyi this doesn't happen to me with every vehicle https://www.kapwing.com/videos/663028c4f4e49a37cd3b9eed. THANKS
      Lauty in Window Tinting - General Discussion
    7. 8

      Applying PPF profitable?

      Do you want to make your business highly profitable and have accurate fast patterns with minimal waste of your film? you can go from scan to pattern faster and you won't have any waste of your film. Please check this video:
      ExactFLat 3D to 2D in Paint Protection Film, Clear Bra Forum
    8. 8

      Air80 vs Stratos70 Windshield

      80% meters 69 on an f-150 shield with the sound screen option
      no ma'am in Window Tinting - General Discussion
    9. 3

      High speed material feed

      The Graphtech plotters are all about the same from 7000 to 8600. I doubt that the machine was the problem If changing software fixed the issue.
      Dano in Plotters and Cutting Systems
    10. 3

      High speed material feed

      Update to this.... We were using a Graphtec FC7000-100 plotter and the Digi Cut software and the machine wouldn't work correctly. We contacted Digi and they did a live modification on our software which solved the issue. Strange thing, the plotter would still never cut through the pattern consistently. (parts would cut totally through and parts would not cut even through the film) We switched to Core and instantly everything cut 100% consistent and without need for software modification. Perhaps if we had a newer plotter than the FC7000 perhaps the Digi would work as expected ??? Dunno
      TTS in Plotters and Cutting Systems
×
×
  • Create New...