-
Posts
26,224 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Subscriptions
Posts posted by Booms
-
-
That is definitely installer error. You can see where his tool went past the film when he was shrinking it, scratching the glass. I mean, what is this installer using to shrink the film? A metal puitty kniife?
I would NOT take no for an answer from this shop. That is what they have insurance for.
- alberts316 and Bham
- 2
-
As stated above, fingers are caused by under shrinking or improper squeegee technique. All a finger is, is excess film OR tension where it shouldn't be...or a combination of both.
Next time your doing a back window, pay attention to what you are doing when the finger appears.
And stop doing the "+" pattern on your squeegee technique. You are causing yourself problems with that.
Question...for finishing the bottom of the film, how do you squeegee? Be specific.
You're welcome.
-
-
On 12/16/2020 at 3:36 PM, Bham said:
-
As a flat rate technician at a dealership, it is your responsibility to negotiate the best terms possible for your services.
Since we don't pay for product you should be in the $100.00 + range to install hood/fenders/mirrors and the same for a bumper.
Depending on your experience of course.
-
I also work for a dealership 5 hours for 16" hood/fender/mirrors and another 5 hours if they want the bumper done.
It also depends on what your flat rate is.
-
That is bad ass.
-
-
You need a compressor with a good air gun. Hose the window down with water, and then blow all the junk out of that rubber gasket. Otherwise you will never get it clean.
You're welcome.
-
-
-
WHAT'S A BOLLOCK
-
The reason is called light refraction. The tint bends around the defroster lines causing a distortion that the light *refracts* off of due to the uneven surface.
No, you can't do anything about it.
You're welcome.
- florida tinter, jconnors and no ma'am
- 2
- 1
-
-
If you're that worried about a trimmed gasket, you got bigger problems than a 1/16th of an inch trim job that you said yourself looked flawless.
Quit obsessing and enjoy your window tint.
-
1) Yes, in some circumstances. I don't do it, but that doesn't mean it's wrong. And if you can't tell that he did it, why worry?
2) Yes, the 3M logo is not on every square inch of the film, so if you have a smaller window, it may not be on that particular piece.
You're welcome.
-
31 minutes ago, pbalentine said:
1500 grit...
^ This...
-
13 hours ago, Capital PPF_Norm said:
IS THAT A FRICKING FLYING JETSKI OR HOVER MOTORCYCLE OR WHAT???
-
-
-
Soap build up in your bottles. Get a scrub brush that will fit in your bottles and scrub the inside of them.
You're welcome.
-
That looks like what Quantum used to do when you wet shrank it...
-
You can't let any water get into the door switches or outside mirror adjuster button on these new Toyotas. The Prius is famous for that. Once it dries, it should be alright,
-
8 hours ago, Old timer said:
Peoples!
Tinter Wanted - Ocala Florida
in Classifieds • Employment • Marketplace
Posted
DeLuca Toyota in Ocala Florida is looking for a top flight window tinter . No beginners. This is an opportunity to make as much money as you want.
This job isn't going anywhere either. Ownership and management are committed to tinting as many vehicles as possible.
• Your own Air Conditioned Bay
• Plotter
• Unlimited cars
• No waiting for someone to give you work. Go to the lot, get a car and tint it
• Competitive pay
• Monday - Friday 8 to 5 ... maybe 1 Saturday a month. Saturdays are 8 - 12
Available Benefits:
• Medical
• Dental
• 401K
• Paid vacation
Please contact Jen Flaherty • 352-732-0770