Paintless Dent Repair & Vehicle Wraps
770 topics in this forum
-
- 1 reply
- 506 views
Hey guys, I am not sure if this is even the right place to be asking this but I just picked up a fairly large vinyl wrap from eBay and the quality is great but there is no transfer paper. It only has one sheet then the sticker is stuck to it. I needed help on the best way to to install it without transfer paper. It Is very big. It 80 inches long and 30 inches tall. Thank you!
Last reply by drtint, -
- 10 replies
- 1.9k views
Hey guys, I am from Lithuania, and there are lots of crappy looking cars in our country, so I would like to open a wrapping business which could be affordable for everybody. Can you pls advise the cheapest options possible? What's the cheapest amount I could charge for a car and still make some money? Thank you!!
Last reply by watchdaride, -
- 1 reply
- 524 views
Getting a shop van wrapped . to get a clear picture like the one attache . What resolution do you need ? was told 300 dpi . Could i use any thing smaller . Its for a astro cargo van
Last reply by Midtown Houston, -
- 0 replies
- 485 views
Graphic and Wrap installer needed. Must have experience and attention to detail a must! Positive attitude Plant City Shop Start right away. Please call 813-719-8780 tintpluspc@gmail.com
Last reply by TINTING PC, -
- 2 replies
- 690 views
I wrapped my whole car successfully. However, my front bumper doesn’t fit on the car after I wrapped. First, I removed my bumper. Second I removed all of the grills and install the bumper back. Third, I wrapped it and removed back to install grills. Finally, I tried to put my bumper back on, but it doesn’t fit. Does anybody know what is the reason?
Last reply by Yusa, -
- 0 replies
- 852 views
I am new at wrapping. I have watched tons of video. I have put stripes on my Jeep with no problem. I am good on hoods or body panels, but I am trying to wrap the fenders and this is proving to be tough. I have the Sahara with the painted fenders but I want them wrapped in a different color. Have any of you seen video on how to wrap the jeep fenders? They stick way out and have lots of curves. I can get the flat surfaces just fine, but it gets bunched up in the inside corners of the fenders and I haven't figured out how to straighten that out. I appreciate any help! Thanks!
Last reply by iwannabfishn, -
- 1 reply
- 1.1k views
I got my car wrapped about 2 months ago in Avery Dennison Gloss Light Blue by a reputable shop in CA. After the initial wrap, a suction cup-looking mark showed up on the trunk. It bagged at my OCD for a bit but they told me sometimes there will be imperfections in the adhesive and that it’s just unavoidable sometimes. I got over it. Now 2 months later, it seems that these marks are increasing in presence, mostly on the vertical surfaces. There HAS to be a fix to this right? It’s driving me crazy. I don’t want to see my money go to waste and have to get it redone. If that is the case I’m just going to get my car Autodipped. But does anyone know of what is happe…
Last reply by Jake, -
- 0 replies
- 475 views
In need of experienced vehicle wrap installers for a busy shop in the Atlanta area. We perform a lot of color change wraps as well as vehicle accents and commercial jobs. Full time and part time work is available. Contact Mark. 404-596-8468
Last reply by thetintpro, -
- 1 reply
- 659 views
Hey everyone, So I just got the new 2018 Honda Accord Sport 2.0T in white and I wanted to wrap the roof in vinyl black. However, I found out that Honda manufactured the car so that the roof and the sides are one piece (ive attached a link to the images). I really dont know much about car wraps but I watched videos where people wrap the roof of their cars and the wraps were folded into the gaps that separate the roof and the side door piece, which was then covered by that black trim piece. I was wondering if wrapping my roof is still possible and whether there are any other solutions. Thanks. https://imgur.com/a/0ZhgY
Last reply by highplains, -
- 6 replies
- 1.2k views
I have a few questions I'm hoping someone can answer for me. I live in the southeast (USA) and environmental conditions are different when comparing the Northeast vs Midwest vs Southeast vs Southwest etc. If a car is not garage-kept, will wrap withstand the sun, rain and heat in hot climate? And particular type one should use in this type of climate? How long before it looks shabby?
Last reply by David Waner, -
- 0 replies
- 615 views
I have some peeling on a Vinyl wrap under my door handle and I want to re-secure it. Any ideas?
Last reply by kaylex, -
- 4 replies
- 1.1k views
Wholesale custom shop mid cities customizing over 80 trucks a month. we are looking for a Full time tinter, wrap installer, and hydro graphics artist! We currently customize vehicles for over 20 dealerships in the DFW area and have a huge demand for graphics and Hydro dipping amazing opportunity working with some really cool vehicles in a very busy shop very professional if you don't have your a game don't bother replying Thank you. Shoot me an email at Addisonmiller102314@gmail.com We have all the equipment - tank and customers - we are just missing you!
Last reply by drtint, -
- 1 reply
- 1.1k views
Hi All, I was hoping for some advice and insight into what the best option is. I am organising a vehicle wrap for a couple of trucks and have contacted a few suppliers and they have pushed latex and vinyl options. The trucks will be around heavy industrial work (there is hydraulic acid in the facility), but the trucks won't touch it, just be near it. Anyone have experience and advice as to which is the better material? I am assuming the wraps would last for 3 - 4 years and from there they would need a refresh. Cheers!
Last reply by Outdoorfunguy85, -
- 2 replies
- 908 views
Newbie to wrapping wondering how to wrap corners without creases or crow feet? Cant seem to do it without it creasing or shrinking back
Last reply by drtint, -
- 0 replies
- 594 views
Hello all!I had a customer string me along with a wrap project, only to have him cancel on me.. Now I am stuck with this roll of supreme wrap vinyl that I can't use and can't return (I missed the 30 day cutoff on Feller's return policy).It is a full roll (60"x25yd) of AVERY SUPREME WRAP COLOR CHANGE VINYL, color is 5294 ORANGE.Still in the box, untouched... $550 roll of material- make me an offer!Can ANYONE take this off my hands??
Last reply by SIGNARAMA TRAVIS, -
- 9 replies
- 3.6k views
This is a bit of an odd one, but I'm hoping someone here with vinyl wrapping experience can help. I am in the process of wrapping a PC case, and am having serious trouble figuring out how to wrap over and cut out for a small 1cm diameter hole. It's basically where a 3.5mm audio jack goes, but I cannot figure out how to do this and maintain a perfect circle where the vinyl wraps around the edge. I tried making cuts in a cross formation, but it ends up looking like a hexagon, not a perfect circle. Any tips on how I can achieve this. It is a very fiddly small shape. Thanks.
Last reply by highplains, -
- 14 replies
- 3.5k views
We have some pretty awesome projects roll though our doors. Thought I would share a few of the cool wraps we have recently designed, printed and installed . I love my job!
Last reply by Car wrap kent, -
- 0 replies
- 560 views
I purchased a fiberglass hardtop that is primered. It needs to be sanded and reprimered. I was going to have it painted but my question is can newly primered fiberglass be successfully wrapped? Will it still be able to be removed without damaging the fiberglass?. If so how long after its primered can it be wrapped? thanks in advance
Last reply by Jbauer, -
- 1 reply
- 792 views
Hi there, I have a white car that had it's roof and hood wrapped in matte vinyl, and after 2 years it looks unsightly therefore custy wanted wrap removed. With the vinyl lifted the white car now is now coloured beige - and that is with the gummy adhesive removed! Any ideas on removal of what seems to be adhesive that has leached into the clear coat ? Otherwise a respray seems to be the only option? Thanks
Last reply by WearTheFoxHat, -
- 2 replies
- 1.1k views
Any suggestions on keeping vinyl long term in the Body Indention at rear sides and rear with no glass on the Transits? I've wrapped quite of few now and I always use the same process. I have a few come back after a month or so with lifting. I always use 3M 94 primer and post heat. Any other installers struggling with this? Forgot to mention...I'm using 3M 1080CV3 with 8518 Lam.
Last reply by BlackInkWraps.com, -
- 7 replies
- 1.4k views
I bought r-vinyl years ago and it sucked. So pretty much I had a bad expierence with wrapping tail lights. I have been getting to many requests and just bought a roll of oracal light gray. Whats your take and do you remove tail lights of leave them on the car?
Last reply by flipflopless, -
- 0 replies
- 375 views
Hello! im looking for some good sign vinyl brand. We just now use oracal 651 but What more we have? No expensive vinyl. Thanks guys!
Last reply by tintswe, -
- 7 replies
- 1.7k views
anybody else still check this forum......for pdr tips or advice.......
Last reply by davebheam, -
Hi folks, I'm a 70 year old newbie to this process. I'm a former Industrial Arts Teacher and obsessive DIY'r. I'm a member of a Corvette club in northern NJ, and love modifying the appearance of my car. I discovered wrap a few years ago and truly enjoy it. My current project is to re-wrap my radio bezel and other hard bits on my dash. The radio bezel is going to be for the 5fth time! I used the wrong materials, overstretched and ripped other applications and thought I had the last one pretty good. (Arlon CF). However, after about a year, it is lifting in some of the inside corners near the HVAC and radio. I was hoping for some advice on how to prevent that this t…
Last reply by Chasboy, -
- 1 reply
- 656 views
Im a trainee in a wrap shop here in the uk and i need some help with directional wrap ukno the ones which change colour when looking at it from different angles. im wondering where you can lay it in any order or will the wrap need to be kept in a certain orientation to match?
Last reply by Supreme, -
- 2 replies
- 430 views
Looking for a 3M certified installer to install a full wrap on a 2017 Jaguar F type convertible in the LA, Santa Monica area. Possible Print and install, but probably install only. Thanks!
Last reply by APTinting-Becky, -
- 4 replies
- 921 views
Can anyone help me out or point me in the right direction where to get a cut file for the hellcat racing stripes pref the charger style??? Nost of my graphic customers are mopar so also does anyone know where i can get other mopar eps files such as the side body lines and hood lines etc???????? Thank you in advance for any help
Last reply by palmettotint, -
- 7 replies
- 2.1k views
I've watched PDR guys pull dents and just curious if anyone thinks a glue tab would pull these? My car got beat up by some Albertan hail a while back.
Last reply by PoopcornPoppers, -
- 1 reply
- 773 views
the dent is situated on the edge of the door. the door edge is rather thick, double panel. Will an edge tool do the trick?
Last reply by Dentpusher, -
- 6 replies
- 4.4k views
this dealership near Cleveland Ohio had hail damage through out there lot... they are announcing five to eight thousand dollars off of vehicles, I was just curious to some experienced people what you have seen prices ranging for repair from not so much damage to alot of damage ??? thank you in advance I am curious because I am interested in purchasing a car I by no means have any experience pulling dents
Last reply by Dent Less, -
- 6 replies
- 1.5k views
I'm in my 21st year of PDR, hail, extreme dent repair. Please ask any question you'd like. From basic pdr training to business building. From hail to door dings. Shoot!
Last reply by Dawnn22, -
- 1 reply
- 491 views
Looking for an experienced designer to create ready to print vehicle wraps.. Give me a shout wnyav1@gmail.com
Last reply by APTinting-Becky, -
- 3 replies
- 705 views
I am a full time tint shop. And would like to add automotive wrap also commercial (box trucks, ect) has anyone had a good experience with any classes out there? Please let me know. Appreciate the feed back
Last reply by watchdaride, -
Hello everyone its my first post here in this grate forum.I would like to know anybody tested Teckwrap American brand carwrap film.If someone have expirience with this brand pls lets shere some info.Becouse im thinking to wrap my car but i dont want to spend 1000 euros for one roll.I knew that 3m,Oracle etc is the best but very expensive Thanks
Last reply by Alexmotaf, -
- 0 replies
- 421 views
Extreme Autoworks is a busy after market accessories shop that specializes in Window Tint, Clear Bra and Vinyl Wrap instillation and is looking for a professional and experienced installer. All installers are hired on a contract basis. We are looking for an experienced Vinyl Wrap Installer! Pay is based on a per square foot basis for installation. If you can also install window tint and clear bra that is a plus and you then would be paid additionally for those installations as well on a per job basis.This person must be someone who takes pride in their work, has good morals and ethics, and is looking for great place to work. Please view our website at www.extremeaw.com fo…
Last reply by extremeawtint, -
- 0 replies
- 389 views
Hi all! Just tooting my own horn here.... I've never been published before! http://www.nxtbook.com/nxtbooks/STMG/sott_201703/#/44
Last reply by APTinting-Becky, -
- 5 replies
- 5k views
I am working on some projects using 5mm MS steel plate in large irregular sizes. I am thinking to vinyl wrap these instead of powder coat painting the pieces. These pieces will stay indoors. I reading various posts regarding wrapping of bare or primered car surfaces there seems to be issues with unpainted surfaces being wrapped. Since my projects will not be exposed to the eviromental elements, can anyone give me any advice? Need and quality of pre-paint work? Type and quality of vinyl? Thanks
Last reply by palmettotint, -
- 0 replies
- 557 views
Hi everyone, I have a Graphtec plotter. Does anyone know if I can buy graphic patterns only, to cut it myself without having to subscribe to a software or pay for a full yearly software licence? I install PPF and vinyl graphics, right now I use 3M Digital Designs for my PPF templates and they have PPF only, with a few tint cuts. So I'm wondering if any company out there sell only the design that I could for instance, cut it myself using Graphtec Cutting Master or any other cutting software. I contacted Film and Vinyl Designs and they were awesome, but I'm not familiar with the graphic designs that they carry and my installations for graphics are not on that volume yet…
Last reply by cartechny, -
- 0 replies
- 413 views
Please help me to find right foil color for red bull mini wrap. Especially for aluminium chrom color similar like on the cans - red bull simply cola... thank you ! Martin
Last reply by MartyX, -
- 4 replies
- 3.3k views
Hey Guys! I'm new to the whole Vinyl Wrap community and figured I'd join a forum and post for some knowledge and assistance!! So I've decided to wrap a Del Sol I have just for fun. I simply want to learn a new skill while at the same time make the car look good. I say that to say that I do have the option to get my car painted, I simply choose not to because I find vinyl wrapping extremely intriguing. That being said, I did the first thing professional wrappers tell you not to do. I purchased cheap ebay here: http://www.ebay.com/itm/262298522623?_trksid=p2060353.m2749.l2649&var=561472803192&ssPageName=STRK%3AMEBIDX%3AIT Some say that it is possible to install …
Last reply by waxworkz,
-
Sponsored by
.png)
-
Activity Stream
-
3
High speed material feed
The Graphtech plotters are all about the same from 7000 to 8600. I doubt that the machine was the problem If changing software fixed the issue. -
3
High speed material feed
Update to this.... We were using a Graphtec FC7000-100 plotter and the Digi Cut software and the machine wouldn't work correctly. We contacted Digi and they did a live modification on our software which solved the issue. Strange thing, the plotter would still never cut through the pattern consistently. (parts would cut totally through and parts would not cut even through the film) We switched to Core and instantly everything cut 100% consistent and without need for software modification. Perhaps if we had a newer plotter than the FC7000 perhaps the Digi would work as expected ??? Dunno -
1
2013 Suzuki Kizashi
Hi Bobby, sorry for the confusion, the makes and models section here is for tinting windows, not performance related. -
1
-
2
What is an established commercial/residential business worth?
I sold my business in '96 that had as assets: tools and inventory and goodwill. I bought it 2.5 years earlier for 5k. It had a gross sales # around 30K and very little goodwill since the owner only worked it part time. In the 2.5 years I ran the company, gross sales went from 30K upward to 177K as a one person operation. To be fair, the final year @ 177K included an installation sale involving 35K sq ft. Still I increased the gross from 30K to 100K under my direction in the 2.5 years of ownership. I sold the business in a short sale for 10K because I landed a corporate job at a film manufacturing company. I lacked the desire to further expand the business, but it was considered reputable even by my competitors. One of them bought it. Don't know if that helps but, maybe you'll find this helpful in determining the goodwill of the one you are considering buying. https://www.freshbooks.com/hub/accounting/calculate-goodwill- 1
-
-
0
Window Tinter for hire in Rockville, MD
Must have experience and knowledge in the automotive window tint industry. This job requires people skills, a positive attitude and willingness to be a team member are essential to this position. Having experience operating a window tint plotter a plus. Pay will be determined during interview process. Please Call TJ Flores 301 979-1313 -
2
What is an established commercial/residential business worth?
Gross 50-60? You could find that kind of revenue picking up cans. Whatever you're about to spend should be spent to market your own brand unless I'm reading this wrong. -
2
What is an established commercial/residential business worth?
Looking to buy an established commercial/residential business. The company has grossed about 50-60k annually for the past few years. There's not really anything as far as assets go. So I'd basically be buying the phone number and 25+ years of being an established business. Just trying to get an idea of what I should be paying! Thanks in advance!! -
1
-
8
Removable rigid window tint sheets - WTF?
Sucks that you got screwed. Sorry to hear that. But that is what we all kinda figured.- 1
-
-
